XGD10603NR Littelfuse

Reference Dimensions: 1.66 +/- 0.06 (0.066 +/- 0.003) 1.04 0.15 +/- 0.08 (0.041 ) REF (0.006 +/- 0.003) Xtreme-Guard ESD Suppressors 0.36 (0.014 ) Surface Mount Polymeric Electrostatic Discharge Suppressors0.84 +/- 0.05 (0.033 +/- 0.002) XGD Series 0.43 +/- 0.18 (0.017 +/- 0.007) Description Wave Solder Reow Solder TM XTREME-GUARD ESD Suppressors protect sensitive electronic equipment against extreme ESD conditions, in very small 0402 and 0603 footprints. This series product is 0.51 (0.020 ) 0.76 (0.030 ) specifically designed to suppress fast-rising ESD transients up to 30kV while adding virtually no capacitance to the 3.05 3.30 circuit, which helps preserve signal integrity and minimize (0.120 ) (0.130 ) data loss. It is a RoHS compliant, halogen free, and Pb free ESD Suppressor. 1.27 (0.050 ) 1.27 (0.050 ) 0.76 (0.030 ) 0.76 (0.030 ) Features High ESD Rating up to Compatible with 30kV Contact/Air pick-and-place processes Discharge A vailable in 1000, 5000, Equivalent Circuits RoHS compliant, lead-free and 10000 piece reels and halogen-free (EIA-RS481) Equivalent Circuit 0402 & 0603 Devices Ultra-low capacitance High rated v oltage up to Low leakage current 32V maximum 1 2 Fast response time High operating Bi-directional temperature at 125C W ithst ands multiple Life Support Note: ESD strikes Not Intended for Use in Life Support or Life Saving Applications The products shown herein are not designed for use in life sustaining or life saving applications unless otherwise expressly indicated. Product Characteristics Applications Wearable Devices Set Top Boxes Part Lines Component Available as Number Protected Package Halogen-Free Notebooks/Laptops/PCs Networking and Wireless XGD10402 1 0402 Yes Gaming Consoles Hardware Smart TVs Stationary and Portable XGD10603 1 0603 Yes Smart Phones Medical Devices Tablets Electrical Characteristics Specification XGD10402 XGD10603 Notes The ESD capability measured by direct and air discharge method is ESD Capability: subject to testing equipment and conditions. Numerous factors could IEC 61000-4-2 Contact Discharge (typical) 30kV 30kV affect the reliability and reproducibility of the direct and air discharge IEC 61000-4-2 Air Discharge (typical) 30kV 30kV test results. Trigger Voltage (typical) 250V 400V Measured per IEC 61000-4-2 Clamping Voltage (typical) 40V 40V 8kV Direct Discharge Method Trigger Voltage (typical) 150V 300V Measured using 500V TLP Direct Discharge Method Clamping Voltage (typical) 40V 28V Rated Voltage (maximum) 24V max 32V max Capacitance (typical) 0.04 pF 0.09 pF Measured at 250MHz Response Time <1nS <1nS Leakage Current (typical) <1nA 24V <1nA 24V 1000 1000 Some shifting in characteristics may occur when tested over multiple ESD Pulse Withstand pulses min pulses min pulses at a very rapid rate Note: Testing performed on Littelfuse test setup as described in Typical Test Setup Section on page 4 of this document. 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/31/20Xtreme-Guard ESD Suppressors Surface Mount Polymeric Electrostatic Discharge Suppressors Signal Integrity: USB3.0 5Gbps Signal Integrity : USB3.0 5Gbps Signal Integrity : USB3.0 5Gbps Without XGD Device With XGD Device Without XGDWith XGD Device Without XGDWith XGD Device Signal Integrity : USB3.0 5Gbps Signal Integrity : USB3.0 5Gbps Without XGDWWithout XGDWith XGD Device ith XGD Device Signal Integrity : USB3.1 10Gbps Signal Integrity : USB3.1 10Gbps Without XGD With XGD Device Without XGD With XGD Device Signal Integrity: USB3.1 10Gbps Without XGD Device With XGD Device Signal Integrity : USB3.1 10GbpsSignal Integrity : USB3.1 10Gbps Without XGD Without XGD With XGD Device With XGD Device Typical Device Capacitance Typical ESD Response 1.00 XGD10603 0.10 XGD10402 XGD10603 XGD10402 0.01 100 1,000 10,000 Frequency (MHz) 2020 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/31/20 Capacitance (pF)