MAAP-010512 Amplifier, Power, 0.8 W Rev. V4 40.5 - 43.5 GHz Features Functional Schematic Gain: 22 dB P1dB: 27 dBm High Linearity, OIP3: 38 dBm Integrated Power Detector Lead-Free 7 mm Laminate Package RoHS* Compliant and 260C Reflow Compatible Description The MAAP-010512 is a 4-stage, high linearity 1W power amplifier in a 7x7 mm laminate package, allowing easy assembly. This PA product is fully matched to 50 ohms on both the input and output. It is designed for use as a power amplifier stage in transmit chains and is ideally suited for 42 GHz band point-to-point radios. Each device is 100% RF tested to ensure performance compliance. The part is fabricated using an efficient pHEMT process. 1,2 Pin Configuration Pin No. Function Pin No. Function Ordering Information 1 RF 9 RF IN OUT 2 V 1 10 V 3 Part Number Package G D 3 V 2 11 V 2 MAAP-010512-000000 Bulk quantity G D 4 V 3 12 V 1 G D MAAP-010512-TR0200 200 Piece Reel 5 No Connection 13 No Connection MAAP-010512-TR0500 500 Piece Reel 6 No Connection 14 No Connection MAAP-010512-001SMB Sample Evaluation board 7 V 15 No Connection REFERENCE 8 V 16 No Connection DETECTOR Paddle Ground 1. MACOM recommends connecting unused package pins to ground. 2. The exposed pad centered on the package bottom must be connected to RF and DC ground. * Restrictions on Hazardous Substances, European Union Directive 2002/95/EC. 11 1 M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: MAAP-010512 Amplifier, Power, 0.8 W Rev. V4 40.5 - 43.5 GHz Electrical Specifications: Freq: 40.5 - 43.5 GHz, VD = 4 V, ID1 = 217 mA, ID2 = 300 mA, ID3 = 600 mA, T = 25C A Parameter Units Min. Typ. Max. Small Signal Gain dB 18.0 22.0 27.0 Gain Flatness cross Band dB - +/-1.0 - Input Return Loss dB - 15 - Output Return Loss dB - 12 - Reverse Isolation dB - 50 - Output P1dB dBm - 27.0 - Output IP3 dBm 32.5 38.0 - Saturated Output Power dBm 25.0 29.0 - Output IMD3 with Pout (scl) = 14 dBm dBc 37.0 48.0 - 3 Supply Current mA - 1117 1300 3. Adjust Vgs between 1.0 V and 0.1 V to achieve specified supply current. Typical current 1117 mA = 217 (ID1) + 300 (ID2) + 600 (ID3) 4,5,6 Absolute Maximum Ratings Handling Procedures Please observe the following precautions to avoid Parameter Absolute Max. damage: Drain Voltage +4.3 V Gate Bias Voltage -1.5 V < Vg < 0 V Static Sensitivity Gallium Arsenide Integrated Circuits are sensitive Input Power 15 dBm to electrostatic discharge (ESD) and can be 7 Junction Temperature 150C damaged by static electricity. Proper ESD control Operating Temperature -40C to +85C techniques should be used when handling these Human Body Model Class 1A devices. Storage Temperature -55C to +150C 4. Exceeding any one or combination of these limits may cause permanent damage to this device. 5. M/A-COM Technology Solutions does not recommend sustained operation near these survivability limits. 6. Operating at nominal conditions with TJ 150C will ensure 6 MTTF > 1 x 10 hours. 7. Junction Temperature (T ) = T + jc * (V * I) J C Typical thermal resistance ( jc) = 11.2 C/W. a) For T = 25C, C T = 75C 4 V, 1117 mA J b) For T = 85C, C T = 135C 4 V, 1117 mA J 22 2 M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: