Cree XB-D Color Series on Board Cree XB-D Color Series Cree XLamp XB-D color LEDs extend the double lumens-per-dollar performance of the XB package to color LEDs, delivering up to 40% higher maximum light output than XP-E color LEDs. The combination of performance and small size of XB-D color LEDs enable better color mixing and lower system cost. FEATURES APPLICATIONS > Cree s smallest lighting class LED: 2.45 x 2.45 mm > Non-Directional > 1A Maximum Drive Current > Directional > Wide viewing angle: 115(white) to 140 (red) > Downlight > Electrically Neutral Thermal Path > Consumer Portable FLUX CHARACTERISTICS 85C COLOR DWL (nm) KIT USED MIN.FLUX (LM) 350MA Blue 465-485 35.2 0Z01 Green 520-535 93.9 0B01 Red-Orange 610-620 80.6 O901 Red 620-630 67.2 O701 CHARACTERISTICS UNIT MINIMUM TYPICAL MAXIMUM Thermal resistance, junction to solder point - white, royal blue, blue C/W 6.5 Thermal resistance, junction to solder point - green C/W 11 Thermal resistance, junction to solder point - amber C/W 7 Thermal resistance, junction to solder point - red-orange, red C/W 5 Viewing angle (FWHM) - white degrees 115 Viewing angle (FWHM) - royal blue, blue, green degrees 135 Viewing angle (FWHM) - amber, red-orange, red degrees 140 Temperature coefficient of voltage - white mV/C -2.5 Temperature coefficient of voltage - royal blue, blue, green mV/C -3.3 Temperature coefficient of voltage - amber, red-orange, red mV/C -2 ESD classification (HBM per Mil-Std-883D) Class 2 DC forward current mA 1000 Reverse voltage V -5 Forward voltage ( 350 mA, 85 C) - white V 2.9 3.5 Forward voltage ( 350 mA, 25 C) - royal blue, blue V 3.1 3.7 Forward voltage ( 350 mA, 25 C) - green V 3.3 3.9 Forward voltage ( 350 mA, 25 C) - amber, red-orange, red V 2.25 2.6 LED junction temperature C 150 It is highly recommended for the user to review the CREE XBD Series page for additional and most recent technical data at: Cree XB-D Color Series on Board * Exceeding maximum ratings may damage the LED and cause potential safety hazards. * Elevated operating temperatures can be expected to negatively impact the service life (lumen output) * All data is related to entire assembly. Data reflects statistical mean values. Actual data may differ depending on variances in the manufacturing process. * End users need to take into account the lumen depreciation as the temperature rises with various thermal solutions installed. Note 1: Using continuously under elevated loads (i.e. the application of high temperature/current/voltage or a significant change in temperature, etc.) may cause this product to significantly decrease in reliability even if the operating conditions are within the absolute maximum ratings. Note 2: The thermal resistance from the LED junction to ambient temperature, Rth(j-a), should be kept below 10C/W so that the LED is not exposed to a condition beyond the absolute maximum ratings. Note 3: The temperature of the LED assembly must be measured at the TC-point according to EN60598-1 in a thermally constant status with a temperature sensor or a temperature sensitive label. Hardware (not included) > Mount with 4 Machine Screws. > 16AWG Maximum Wire Gauge. > Use only with constant current power supplies. PCB Fabrication > Layer Count: 1 > Core Material: 6061-T6 Aluminum > Single Layer Copper Weight: 1oz > Solder Mask: White > Finishing Plating: Pb Free HASL Global Headquarters, 3 Northway Lane North, Latham, NY 12110, USA www.marktechopto.com TOLL FREE: 1-800-984-5337 PHONE: 518-956-2980 FAX: 518-785-4725 EMAIL: info marktechopto.com