SP3070E - SP3078E Family Data Sheet 15kV ESD-Protected, 3.3V, 1/8 Load, Failsafe RS-485/RS-422 Transceivers General Description Features The SP3070E - SP3078E differential line transceivers are 15kV ESD protection for RS-485 pins suitable for bidirectional communication on balanced 3.3V low-power operation multi-point bus transmission lines and comply with both RS-485 and RS-422 EIA Standards. Each device consists Advanced receiver-failsafe protection for open, shorted of a differential driver and differential receiver. All devices or terminated lines operate from a 3.3V power supply. Up to 256 transceivers may share Bus High receiver input impedance allows a large number of Very low load for 8x greater fanout transceivers to share a common data bus while maintaining signal margin and without excessive loading Hot Swap glitch protection RE and DE or use of expensive repeaters. The high impedance driver Thermal shutdown protects against driver contention output is maintained over the entire common-mode Available in three industry standard footprints voltage range from -7 to +12V. Receivers will failsafe to logic 1 output when inputs are open, shorted or SP3070E, SP3073E and SP3076E in Full-Duplex terminated. Drivers include built-in short-circuit protection (14-pin) and a thermal-overload shutdown to protect against SP3071E, SP3074E and SP3077E in Full-Duplex excessive power dissipation from bus contention or cable (8-pin) faults. All RS-485 receiver inputs and driver outputs are SP3072E, SP3075E and SP3078E in Half-Duplex ESD protected up to 15kV (Air-Gap and Human Body (8-pin) Model) and up to 8kV Contact Discharge (IEC 61000-4- Three applications-optimized speed grades 2). The SP3070E - SP3078E devices may not achieve SP3070E - SP3072E: 250kbps slew-limited optimal transmit performance if the connected receiver includes a biasing network to 5.0V without a termination SP3073E - SP3075E: 500kbps slew-limited resistor. Please see MaxLinear Application Note ANI 21 SP3076E - SP3078E: 16Mbps high speed for further details. Small form factor NSOIC packages Industrial (-40 to 85C) and Extended (-40 to 125C) temperature grades Applications Ordering Information - page 19 Industrial Control, Utility Meters, Building Automation, Instrumentation, Point of Sale NC 1 14 Vcc RO 2 13 14 PIN NSOIC NC 8 PIN NSOIC 8 PIN NSOIC 1 8 Vcc Vcc 1 8 A RO RE 3 12 A SP3072E SP3071E 2 7 B 2 7 SP3070E RE RO B DE 4 11 B SP3075E SP3074E SP3073E 3 6 3 6 DE A DI Z SP3078E SP3077E DI 5 10 Z SP3076E DI45 GND GND45 Y Half Duplex Full Duplex GND 6 9 Y Full Duplex GND78 NC Figure 1: Pinouts www.maxlinear.com Rev 1.0.3 SP3070E - SP3078E Family RS-485/RS-422 Transceivers Data Sheet Revision History Revision History Document No. Release Date Change Description - Legacy Sipex Datasheet. Convert to Exar format, update ordering information, correct subscript on pages 5-7 and 1.0.0 06/10/09 change revision to 1.0.0. Correct type error on page 7 on driver switching characteristics table. Change 1.0.1 09/30/10 SP3076E,3077E and 3078E Receiver enable time from shutdown from 1800ns to 3000ns. Add reference to Application Note ANI 21 and change ESD protection levels to 1.0.2 12/02/10 IEC 61000-4-2. Update to MaxLinear format, update Ordering Information. Move ESD Protection to page 2. 1.0.3 2/24/20 Corrected 14-pin block diagram (pin 3). 2/24/20 Rev 1.0.3 ii