XR3080-88X HIGH OUTPUT 18V TOLERANT RS-485/RS-422 +5V TRANSCEIVERS JULY 2015 REV. 1.0.2 GENERAL DESCRIPTION FEATURES The XR3080-88X family of high performance RS-485/ 40% Higher SNR (Signal-to-Noise Ratio) 422 devices are designed for improved performance in compared to other RS-485 devices (2.1V vs. 1.5V) noisy industrial environments and increased tolerance 18V Fault Tolerance on Analog Bus pins to system faults. 2.1V Driver Output (Profibus Compliant) The analog bus pins can withstand direct shorts up to Robust ESD (ElectroStatic Discharge) Protection: 18V, and are protected against ESD events up to 15kV IEC 61000-4-2 Air Gap Discharge 15kV. The Profibus compliant differential output deliv- 8kV IEC 61000-4-2 Contact Discharge ers 40% higher SNR than standard RS-485/422 15kV Human Body Model devices, affording additional noise margin or extended 4kV Human Body Model on non-bus pins cable lengths. +4.5V to +5.5V Operation (5V 10%) The receivers include full fail-safe circuitry, guarantee- 300A Idle Current, 1nA Shutdown Current ing a logic-high receiver output when the receiver inputs are open, shorted, or undriven. The receiver Enhanced Receiver Fail-Safe Protection for Open, input impedance is at minimum 96k (1/8 unit load), Shorted, or Terminated but Idle Data Lines allowing up to 256 devices on the bus while preserving Hot-Swap Glitch Protection on DE and RE Pins the full signal margin. Driver Short Circuit Current Limit and Thermal Shutdown for Overload Protection The drivers are protected by short circuit detection as th well as thermal shutdown, and maintain high imped- 1/8 Unit Load Allows up to 256 Devices on Bus ance in shutdown or when powered off. The XR3080- Operating Temperature Range: 85X drivers are slew limited for reduced EMI and error- Industrial -40C to 85C free communication over long or unterminated data Extended -40C to 125C cables. Industry Standard 8 and 14 NSOIC Packages The devices with DE and RE pins include hot swap cir- cuitry to prevent false transitions on the bus during powerup or live insertion, and can enter a 1nA low cur- rent shutdown mode for extreme power savings. The transceivers draw less than 600A from a +5.0V supply, and typically only 300A when idling with the receivers active. TYPICAL APPLICATIONS Motor Control 1 8 RO V R CC Security Systems 2 7 RE B/Z Building and Process Automation 3 6 DE A/Y Remote Utility Meter Reading 4 5 DI GND D Energy Monitoring and Control Long or Unterminated Transmission Lines Profibus DP Fieldbus Networks Exar Corporation 48720 Kato Road, Fremont CA, 94538 (510) 668-7000 FAX (510) 668-7017 www.exar.com X SERIES : EXCELLENCE & RELIABILITYXR3080-88X HIGH OUTPUT 18V TOLERANT RS-485/RS-422 +5V TRANSCEIVERS REV. 1.0.2 ABSOLUTE MAXIMUM RATINGS These are stress ratings only and functional operation of the device at these ratings or any other above those indicated in the operation sections to the specifications below is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability and cause permanent damage to the device. V -0.3V to +7.0V CC Input Voltage at Control and Driver Input (RE, DE, and DI) -0.3V to +7.0V -0.3V to (V + 0.3V) Receiver Output Voltage (RO) CC Driver Output Voltage (A, B, Y and Z) 18V Receiver Input Voltage (A and B, half or full duplex) 18V Transient Voltage Pulse, through 100 70V Figure 6 Driver Output Current 250mA Storage Temperature Range -65C to +150C Lead Temperature (soldering, 10s) +300C Package Power Dissipation 8-Pin SO = 128.4C/W Maximum Junction Temperature = +150C JA 14-Pin SO = 86C/W JA CAUTION: ESD (Electrostatic Discharge) sensitive device. Permanent damage may occur on unconnected devices subject to high energy electrostatic fields. Unused devices must be stored in conductive foam or shunts. Personnel should be properly grounded prior to handling this device. The protective foam should be discharged to the destination socket before devices are removed. 2