9200 Structural Epoxy Adhesive 9200 is a toughened, 2-part epoxy adhesive, designed to create long-lasting load-bearing joints. It creates tough vibration-resistant bonds and is especially useful for joining dissimilar materials that will experience thermal cycling stresses or harsh environmental conditions. This smooth, non-sagging, thixotropic adhesive is excellent for use on vertical surfaces, for gap lfi ling, and for potting electronics enclosures with gaps where a non-thixotropic encapsulant would ofl w through. For a flame retardant version, use 9200FR. Cured Properties Features & Benefits Breakdown Voltage 41 500 V Excellent bond strength to a wide variety of Dielectric Strength 503 V/mil substrates 13 Resistivity 2.5 x 10 cm Extreme resistance to vibration and Hardness 76 D temperature cycles 2 Tensile Strength 16 N/mm Superior tensile, compressive and lap shear 2 Compressive Strength 64 N/mm strength 2 Lap Shear (stainless steel) 20 N/mm Excellent chemical resistance 2 (aluminum) 22 N/mm Excellent electrical insulating characteristics Glass Transition Temperature (T ) 44 C g Low shrinkage CTE Prior T 95 ppm/C g CTE After T 215 ppm/C g RoHS 3 compliant Thermal Conductivity 25 C 0.3 W/(mK) Service Temperature Range -40150 C Available Packaging Cat. No. Packaging Net Vol. Net Wt. Usage Parameters 9200-25ML Dual syringe 25 mL 31.3 g Working Time 30 min 9200-50ML Dual cartridge 45 mL 56.3 g Mix Ratio by Volume 1:1 Mix Ratio by Weight 1:1 Contact Information MG Chemicals, 1210 Corporate Drive Uncured Properties Burlington, Ontario, Canada L7L 5R6 Mixed Density 1.25 g/mL Email: support mgchemicals.com Viscosity 25 C (A) 295 Pas Phone: Nor th America: +(1)80 0 -3 40 - 0772 (B) 170 Pas Shelf Life 3 y International: +(1) 905-331-1396 Europe: +(44)1663 362888 ISO 9001:2015 Quality Management System. Burlington, Ontario, Canada SAI Global File: 004008 06 May 2021 / Ver. 3.1 19200 Application Instructions Dispensing Accessories Read the product SDS and Application Guide for Consult the table below for accessory selection. See more detailed instructions before using this product the Dispensing Accessories Application Guide for (downloadable at www.mgchemicals.com). usage instructions. 8MT-50-FT should only be used with a pneumatic dispenser. Recommended Preparation Cat. No. Dispensing Gun Static Mixer Clean the substrate with Isopropyl Alcohol, MG 824, so the surface is free of oils, dust, and other residues. 9200-25ML N/A N/A 9200-50ML 8DG-50-1-1 8MT-50, 8MT-50FT Syringe or Cartridge 1. Twist and remove the cap from the cartridge or Cure Instructions syringe. Do not discard cap. Allow to cure at room temperature for 48 hours, 2. Dispense a small amount to ensure even flow of or cure the adhesive in an oven at one of these both parts. time/temperature options: 3. (Optional) Attach a static mixer to the 9200-50ML. Temperature 40 C 65 C 80 C 100 C a. Dispense and discard 3 to 5 mL of the product to ensure a homogeneous mixture. Time 16 h 1.5 h 1 h 15 min b. After use, dispose of static mixer. 4. Without a static mixer, dispense material on a mixing Storage and Handling surface or container, and thoroughly mix parts A Store between -10 and 27 C in a dry area, away and B together. from sunlight (see SDS). To maximize shelf life, recap 5. To stop the flow, pull back on the plunger. product firmly when not in use. 6. Clean nozzle to prevent contamination and material buildup. 7. Replace the cap on the cartridge or syringe. Disclaimer This information is believed to be accurate. It is intended for professional end-users who have the skills required to evaluate and use the data properly. M.G. Chemicals Ltd. does not guarantee the accuracy of the data and assumes no liability in connection with damages incurred while using it. ISO 9001:2015 Quality Management System. Burlington, Ontario, Canada SAI Global File: 004008 06 May 2021 / Ver. 3.1 2