24LC64X-I/ST Microchip

24AA64/24LC64 2 64K I C Serial EEPROM Device Selection Table Description: Part VCC Max. Clock Temp. The Microchip Technology Inc. 24AA64/24LC64 Number Range Frequency Ranges (24XX64*) is a 64 Kbit Electrically Erasable PROM. The device is organized as a single block of 8K x 8-bit (1) 24AA64 1.8-5.5 400 kHz I memory with a 2-wire serial interface. Low-voltage 24LC64 2.5-5.5 400 kHz I, E design permits operation down to 1.8V, with standby Note 1: 100 kHz for VCC <2.5V and active currents of only 1 A and 1mA, respectively. It has been developed for advanced, low- power applications such as personal communications Features: or data acquisition. The 24XX64 also has a page write Single-supply with operation down to 1.8V capability for up to 32 bytes of data. Functional address Low-power CMOS technology: lines allow up to eight devices on the same bus, for up to 512 Kbits address space. The 24XX64 is available in - 1 mA active current, typical the standard 8-pin PDIP, surface mount SOIC, TSSOP -1 A standby current (max.) (I-temp) and MSOP packages. Organized as a single block of 8K bytes (64K bit) 2 Package Types 2-wire serial interface bus, I C compatible SOIC, TSSOP PDIP, MSOP Cascadable for up to eight devices Schmitt Trigger inputs for noise suppression A0 1 8 VCC A0 1 8 VCC Output slope control to eliminate ground bounce A1 2 7 WP 2 7 A1 WP 100 kHz (24AA64) and 400 kHz (24LC64) A2 3 6 SCL 3 6 compatibility A2 SCL Self-timed write cycle (including auto-erase) VSS 4 5 SDA 4 5 VSS SDA Page write buffer for up to 32 bytes ROTATED TSSOP Hardware write-protect for entire memory DFN WP 1 8 SCL Can be operated as a serial ROM 1 A0 8 VCC Vcc 2 7 SDA Factory programming (QTP) available 7 WP A1 2 A0 3 6 Vss ESD protection > 4,000V 6 SCL A2 3 A1 4 5 A2 VSS 4 5 1,000,000 erase/write cycles SDA Data retention > 200 years 8-lead PDIP, SOIC, TSSOP, DFN and MSOP packages Block Diagram Pb-free finish available HV WP Generator Available temperature ranges: - Industrial (I): -40C to +85C - Automotive (E): -40C to +125C I/O Memory EEPROM Control Control XDEC Array Logic Logic Page Latches I/O SCL YDEC SDA VCC Sense Amp. * 24XX64 is used in this document as a generic part VSS R/W Control number for the 24AA64/24LC64 devices. 2005 Microchip Technology Inc. DS21189K-page 124AA64/24LC64 1.0 ELECTRICAL CHARACTERISTICS () Absolute Maximum Ratings VCC.............................................................................................................................................................................6.5V All inputs and outputs w.r.t. VSS ......................................................................................................... -0.3V to VCC +1.0V Storage temperature ...............................................................................................................................-65C to +150C Ambient temperature with power applied................................................................................................-40C to +125C ESD protection on all pins ...................................................................................................................................................... 4kV NOTICE: Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. TABLE 1-1: DC CHARACTERISTICS Industrial (I): TA = -40C to +85C, VCC = +1.8V to +5.5V DC CHARACTERISTICS Automotive (E): TA = -40C to +125C, VCC = +2.5V to +5.5V Param. Sym. Characteristic Min. Typ. Max. Units Conditions No. A0, A1, A2, WP, SCL and SDA pins D1 VIH High-level input voltage 0.7 VCC V D2 VIL Low-level input voltage 0.3 VCC V VCC 2.5V 0.2 VCC V VCC < 2.5V D3 VHYS Hysteresis of Schmitt 0.05 VCC V VCC 2.5V (Note 1) Trigger inputs (SDA, SCL pins) D4 VOL Low-level output voltage 0.40 V IOL = 3.0 mA VCC = 4.5V IOL = 2.1 mA VCC = 2.5V D5 ILI Input leakage current 1 AVIN = VSS or VCC, WP = VSS VIN = VSS or VCC, WP = VCC D6 ILO Output leakage current 1 AVOUT = VSS or VCC D7 CIN, Pin capacitance 10 pFVCC = 5.0V (Note 1) COUT (all inputs/outputs) TA = 25C, FCLK = 1 MHz D8 ICC write Operating current 0.1 3 mAVCC = 5.5V, SCL = 400 kHz D9 ICC read 0.05 400 A D10 ICCS Standby current .01 1 A Industrial 5 A Automotive SDA = SCL = VCC A0, A1, A2, WP = VSS Note 1: This parameter is periodically sampled and not 100% tested. 2: Typical measurements taken at room temperature. DS21189K-page 2 2005 Microchip Technology Inc.