MCP6546UT-E/OT Microchip

+ + MCP6546/6R/6U/7/8/9 Open-Drain Output Sub-Microamp Comparators Features Description Low Quiescent Current: 600 nA/Comparator (typical) The Microchip Technology Inc. MCP6546/6R/6U/7/8/9 family of comparators, is offered in single (MCP6546, Rail-to-Rail Input: V - 0.3V to V + 0.3V SS DD MCP6546R, MCP6546U), single with chip select (CS) Open-Drain Output: V 10V OUT (MCP6548), dual (MCP6547) and quad (MCP6549) Propagation Delay: 4 s (typical, 100 mV Overdrive) configurations. The outputs are open-drain and are Wide Supply Voltage Range: 1.6V to 5.5V capable of driving heavy DC or capacitive loads. Single Available in SOT-23-5, SC-70-5* Packages These comparators are optimized for low power, Available in Single, Dual and Quad single-supply application with greater than rail-to-rail Chip Select (CS) with MCP6548 input operation. The output limits supply current surges Low Switching Current and dynamic power consumption while switching. The open-drain output of the MCP6546/6R/6U/7/8/9 family Internal Hysteresis: 3.3 mV (typical) can be used as a level-shifter for up to 10V using a pull- Temperature Range: up resistor. It can also be used as a wired-OR logic. - Industrial: -40C to +85C The internal Input hysteresis eliminates output switch- - Extended: -40C to +125C ing due to internal noise voltage, reducing current draw. These comparators operate with a single-supply Typical Applications voltage as low as 1.6V and draw a quiescent current of less than 1 A/comparator. Laptop Computers The related MCP6541/2/3/4 family of comparators from Mobile Phones Microchip has a push-pull output that supports rail-to- Metering Systems rail output swing and interfaces with CMOS/TTL logic. Hand-held Electronics * SC-70-5 E-Temp parts are not available at this RC Timers release of the data sheet. Alarm and Monitoring Circuits MCP6546U SOT-23-5 is E-Temp only. Windowed Comparators Multi-vibrators Related Devices CMOS/TTL-Compatible Output: MCP6541/2/3/4 Package Types MCP6549 MCP6546 MCP6546R MCP6547 PDIP, SOIC, TSSOP PDIP, SOIC, MSOP PDIP, SOIC, MSOP SOT-23-5 OUTA 1 14OUTD V OUTA 1 NC 1 8 V 8 DD NC OUT 1 5 SS V 2 - + + 13V - INA IND V - + OUTB V 2 - 7 V 2 7 V INA IN DD 2 DD V + 3 12V + INA IND + V + + - V V + 3 6 3 6 OUT INA INB IN V + 3 4 V IN IN V V 4 11 DD SS V V 4 V + 4 5 SS 5 SS NC INB V + 5 10V + INB INC - - + + V 6 9 V INB INC MCP6546 MCP6546U MCP6548 OUTB 7 8 OUTC SC-70-5, SOT23-5 SC-70-5, SOT-23-5 PDIP, SOIC, MSOP V V OUT 1 V + NC 1 8 CS 5 DD 1 5 DD IN V V V V 2 - 7 2 2 DD SS SS IN + V + 3 6 OUT V + 4 V V OUT 3 3 4 IN IN IN IN V 4 5 NC SS 2002-2012 Microchip Technology Inc. DS21714G-page 1 - - + -MCP6546/6R/6U/7/8/9 Notice: Stresses above those listed under Absolute 1.0 ELECTRICAL Maximum Ratings may cause permanent damage to CHARACTERISTICS the device. This is a stress rating only, and functional operation of the device, at those or any other conditions Absolute Maximum Ratings above those indicated in the operational listings of this V - V .........................................................................7.0V DD SS specification, is not implied. Exposure to maximum rat- Open-Drain Output.............................................. V + 10.5V SS ing conditions for extended periods may affect device Analog Input (V +, V -)............. V - 1.0V to V + 1.0V IN IN SS DD reliability. All Other Inputs and Outputs ......... V 0.3V to V + 0.3V SS DD Difference Input Voltage ...................................... V V DD SS See Section 4.1.2 Input Voltage and Current Output Short-Circuit Current .................................continuous Limits Current at Input Pins ....................................................2 mA Current at Output and Supply Pins ............................30 mA Storage Temperature.....................................-65C to +150C Maximum Junction Temperature (T )..........................+150C J ESD Protection on All Pins: (HBM MM) .....................................2 kV 200V (MCP6546U) (HBM MM) ................................ 4 kV 200V (all other parts) DC CHARACTERISTICS Electrical Specifications: Unless otherwise indicated, V = +1.6V to +5.5V, V = GND, T = 25C, V + = V /2, DD SS A IN DD V = V , R =2.74k to V = V (Refer to Figure 1-3). IN SS PU PU DD Parameters Sym Min Typ Max Units Conditions Power Supply Supply Voltage V 1.6 5.5 V V V DD PU DD Quiescent Current I 0.3 0.6 1 A I = 0 Q OUT (per comparator) Input Input Voltage Range V V V + 0.3 V CMR SS DD 0.3 Common Mode Rejection Ratio CMRR 55 70 dB V = 5V, V = -0.3V to 5.3V DD CM Common Mode Rejection Ratio CMRR 50 65 dB V = 5V, V = 2.5V to 5.3V DD CM Common Mode Rejection Ratio CMRR 55 70 dB V = 5V, V = -0.3V to 2.5V DD CM Power Supply Rejection Ratio PSRR 63 80 dB V = V CM SS Input Offset Voltage V -7.0 1.5 +7.0 mV V = V (Note 1) OS CM SS Drift with Temperature V /T 3 V/C T = -40C to +125C, V = V OS A A CM SS Input Hysteresis Voltage V 1.5 3.3 6.5 mV V = V (Note 1) HYST CM SS Linear Temp. Co. TC 6.7 V/CT = -40C to +125C, V = V 1 A CM SS (Note 2) 2 -0.035 V/C T = -40C to +125C, V = V Quadratic Temp. Co. TC 2 A CM SS (Note 2) Input Bias Current I 1 pAV = V B CM SS At Temperature (I-Temp parts) I 25 100 pA T = +85C, V = V (Note 3) B A CM SS At Temperature (E-Temp parts) I 1200 5000 pA T = +125C, V = V (Note 3) B A CM SS Input Offset Current I 1 pA V = V OS CM SS Note 1: The input offset voltage is the center of the input-referred trip points. The input hysteresis is the difference between the input-referred trip points. 2: V at differential temperatures is estimated using: HYST 2 V (T ) = V + (T -25C) TC + (T - 25C) TC . HYST A HYST A 1 A 2 3: Input bias current at temperature is not tested for the SC-70-5 package. 4: Do not short the output above V + 10V. Limit the output current to Absolute Maximum Rating of 30 mA. SS The minimum V test limit was V before Dec. 2004 (week code 52). PU DD DS21714G-page 2 2002-2012 Microchip Technology Inc.