PL130-07(A)
PL130-07
PL130-07(A)
High Speed Translator Buffer to LVCMOS
FEATURES PIN CONFIGURATION
(TOP VIEW)
LVCMOS output
Selectable Drive capability
GND 1 8 DRV_SEL^
Drive 15pF or 30pF output load
Single AC coupled input (min. 100mV swing).
REF_IN VDD
2 7
Accepts LVCMOS or Sine Wave inputs.
GND 3 6 GND
Input range from 0 to 200 MHz.
VDD 4 5 CLK_OUT
OE High (PL130-07) or OE Low (PL130-07A)
Enable
SOP-8L
2.5V to 3.3V operation.
Available in 8-Pin SOP, 8-Pin TSSOP and
VDD 1 8 CLK_OUT
3x3mm 16-Pin QFN.
DRV_SEL VDD
2 7
GND DNC
3 6
DESCRIPTION
OE 4 5 FIN
The PL130-07 is a low cost, high performance, high
TSSOP-8L
speed, buffer that reproduces any input frequency
from 0 to 200MHz. It provides an LVCMOS output
with 15pF output load drive capability. Any input sig-
nal with at least 100mV swing can be used as refer-
12 11 10 9
ence signal. This chip is ideal for conversion from DRV_SEL 13 8
CLK_OUT
sine wave to LVCMOS.
14 7 VDD
GND
PL130-07(A)
15
GND 6 N/C
16
5 GND
OE
1 2 3 4
BLOCK DIAGRAM
Input
REF_IN
CLK_OUT
Amplifier
OE
Micrel Inc. 2180 Fortune Drive San Jose, CA 95131 USA tel +1(408) 944-0800 fax +1(408) 474-1000 www.micrel.com Rev 03/24/15 Page 1
VDD
GND
VDD
GND
REF_IN VDD
GND GND PL130-07(A)
High Speed Translator Buffer to LVCMOS
PIN DESCRIPTION
Name SOP-8L TSSOP-8L QFN-16L Type Description
1,2,4,5,
GND 1,3,6 3 P Ground.
9,14,15
VDD 4,7 1,7 7,10,11,12 P Power supply.
Drive Select input: 1 for standard drive, 0 for hi-
DRV_SEL 8 2 13 I
drive output. Internal pull-up (default is 1).
Reference input signal. The frequency of this signal
REF_IN 2 5 3 I will be reproduced at the output (after translation to
CMOS level).
CLK_OUT 5 8 8 O CMOS clock output.
OE N/A 4 16 I Output Enable. See OE LOGIC TABLE below
OE LOGIC TABLE
Part Number OE State Output Buffer State
0 Tri-State
PL130-07
1 (Default) Active
0 (Default) Active
PL130-07A
1 Tri-State
ELECTRICAL SPECIFICATIONS
1. Absolute Maximum Ratings
PARAMETERS SYMBOL MIN. MAX. UNITS
Supply Voltage V 4.6 V
DD
Input Voltage, dc V -0.5 V +0.5 V
I DD
Output Voltage, dc V -0.5 V +0.5 V
O DD
Storage Temperature T -65 150 C
S
Ambient Operating Temperature* T -40 85
A C
Junction Temperature T 125 C
J
Lead Temperature (soldering, 10s) 260
C
ESD Protection, Human Body Model 2 kV
Exposure of the device under conditions beyond the limits specified by Maximum Ratings for extended periods may cause permanent
damage to the device and affect product reliability. These conditions represent a stress rating only, and functional operations of the
device at these or any other conditions above the operational limits noted in this specification is not implied.
* Note: Operating Temperature is guaranteed by design for all parts (COMMERCIAL and INDUSTRIAL), but tested for COMMERCIAL
grade only.
Micrel Inc. 2180 Fortune Drive San Jose, CA 95131 USA tel +1(408) 944-0800 fax +1(408) 474-1000 www.micrel.com Rev 03/24/15 Page 2