MURS1560A-BP Micro Commercial Components (MCC)

MURS1560A Features Halogen Free Available Upon Request By Adding Suffix-H Lead Free Finish/RoHS Compliant (Note1) Suffix Designates 15 Amp Compliant. See Ordering Information) Epoxy Meets UL 94 V-0 Flammability Rating FRED Rectifiers Moisture Sensitivity Level 1 Low Switching Losses and High Efficiency 600 Volts Low Reverse Leakage Planar Structure Die and Soft Recovery Characteristics Maximum Ratings Operating Junction Temperature Range: -55C to +150C Storage Temperature Range: -55C to +150C Maximum Thermal Resistance: 2C/W Junction to Case TO-220AC Maximum Maximum DC Maximum MCC Device Recurrent Blocking RMS Part Number Marking Peak Reverse Voltage Voltage Voltage L B K M MURS1560A MURS1560A 600V 420V 600V C D Electrical Characteristics 25C Unless Otherwise Specified A Average Rectified I T = 105C 15A C F(AV) Forward Current 1 2 Peak Forward Surge I 160A 8.3ms,Half Sine F FSM Current I =15A T =25C 1.32V(Typ) F J Maximum G I =15A T =25C Instantaneous V 1.6V(Max) F J F I Forward Voltage I =15A T =125C 1.4V(Max) F J N J Maximum Reverse H 5A T =25C J I R Current At Rated DC T =125C 50A J Blocking Voltage Typical Junction Measured at C 100pF J 1.0MHz, V =4.0V Capacitance R DIMENSIONS Dynamic Recovery Characteristics 25C Unless Otherwise Specified INCHES MM DIM NOTE MIN MAX MIN MAX 31ns(Typ.) I =0.5A I =1.0A F R A 0.560 0.625 14.22 15.88 I =0.25A 40ns(Max.) RR Reverse Recovery B 0.380 0.420 9.65 10.67 t rr C 0.100 0.135 2.54 3.43 Time 95ns(Typ.) T =25C J D 0.230 0.270 5.84 6.86 T =125C 145ns(Typ.) J F ----- 0.250 ----- 6.35 I = 15 A F G 0.500 0.580 12.70 14.73 5.0A(Typ.) T =25C Peak recovery J di /dt = 200 A/s H 0.190 0.210 4.83 5.33 F I RRM current T =125C 9.5A(Typ.) J I 0.020 0.045 0.51 1.14 V = 400 V R J 0.012 0.025 0.30 0.64 245nC(Typ.) T =25C Reverse recovery J K 0.139 0.161 3.53 4.09 Q rr charge T =125C L 0.140 0.190 3.56 4.83 710nC(Typ.) J M 0.045 0.055 1.14 1.40 N 0.080 0.115 2.03 2.92 Note :1. High Temperature Solder Exemption Applied, See EU Directive Annex 7a. Internal Structure PIN 1 CASE PIN 2 Rev.3-3-01282021 1/3 MCCSEMI.COMMURS1560A Curve Characteristics Fig. 1 - Forward Current Derating Curve Fig. 2 - Maximum Non-Repetitive Peak Forward Surge Current 20 120 160 15 120 10 80 5 40 Resistive or Inductive Load 8.3 ms Single Half Sine-Wave 0 0 0 25 50 75 100 125 150 1 10 100 Number of Cycles at 60 Hz Case Temperature (C) Fig. 3 - Typical Instantaneous Forward Characteristics Fig. 4 - Typical Reverse Leakage Characteristics 20 100 T =1 50C J T =25C J 10 =100C 10 T =1 25C =125C J =150C 1 T =1 00C J 0.1 0.01 T =25C J 1 0.001 40 60 80 0.4 0.6 0.8 1.0 1.2 1.4 1.6 20 100 Percent of Rated Peak Reverse Voltage (%) Instantaneous Forward Voltage (V) Fig. 5 - Capacitance Characteristics Fig. 6 - Reverse Recovery Waveform and Definitions 300 (3) t rr T =25C J I F t t a b f=1MHz 0 (4) Q rr 200 (2) I RRM 0.5 I RRM (5) di /dt (rec)M di /dt (1) F 0.75 I RRM 100 (4) Q - area under curve defined by t (1) di /dt - rate of change of current rr rr F and I through zero crossing RRM t x I rr RRM (2) I - peak reverse recovery current RRM Q = rr 2 (3) t - reverse recovery time measured rr (5) di /dt - peak rate of change of (rec)M from zero crossing point of negative 0 current during t portion of t b rr going I to point where a line passing F 0 10 20 30 through 0.75 I and 0.50 I RRM RRM Reverse Voltage (V) extrapolated to zero current. Rev.3-3-01282021 2/3 MCCSEMI.COM Average Forward Current (A) Capacitance Between Terminals (pF) Instantaneous Forward Current (A) Peak Forward Surge Current (A) Instantaneous Reverse Leakage Current (A)