2. Soldering the headers Before using your click board , make sure to solder 1x8 male headers to both left and right side of the board. Two 1x8 male headers are included with the board in the package. 1 Touchpad click 2 3 4. Essential features The MTCH6102 device supports taps, doubletaps, swipes and scrolling gestures. The small capacitive surface is optimized for sungle-finger applications. The sensor outputs 12-bit resolution coordinate data (the I2C interface supports up to 400 kbps transfer rates). MTCH6102 also incorporates power-saving features, such Turn the board upside down so that Turn the board upward again. Make sure as a configurable frame rate for sleep/idle the bottom side is facing you upwards. to align the headers so that they are modes, as well as a separate standby and Place shorter pins of the header into the perpendicular to the board, then solder the active mode. appropriate soldering pads. pins carefully. 1. Introduction Touchpad click is a capacitive touch 3. Plugging the board in input device driven by Microchips low- powered MTCH6102 controller. The click Once you have soldered the headers your touchpad surface is covered with a sheet board is ready to be placed into the desired of black plastic to demonstrate the chips BOARDS mikroBUS socket. Make sure to align the cut support for cover layers (up to 3mm for www.mikroe.com in the lower-right part of the board with the plastic, 5mm for glass) Touchpad click markings on the silkscreen at the mikroBUS communicates with the target MCU through socket. If all the pins are aligned the mikroBUS I2C interface (SCL and SDA Touchpad click Manual v100 Touchpad click Manual v100 correctly, push the board all the pins), with additional functionality provided way into the socket. by the Interrupt and RSTL pins. Designed to 0100000091166 use a 3.3V power supply.8. Code examples 5. Schematic Once you have done all the necessary preparations, its time to get your click board up and running. We have provided examples for mikroC , mikroBasic and mikroPascal compilers on our Libstock website. Just VCC-3.3V VCC-3.3V VCC-3.3V C1 download them and you are ready to start. 100nF R3 U1 R4 R5 R6 20K 4K7 1K8 1K8 .com RX11 1 21 RX6 RX11 RX6 R2 AN PWM RX12 2 20 RX5 RST RSTL INT RX12 RX5 RST INT 3 19 RX4 100 NC RX4 CS TX RX13 4 18 RX3 RX13 RX3 SCK RX 5 17 SCL VSS VDD SCL MISO 6 16 SDA NC VSS MOSI SDA 7 15 RX2 NC RX2 +3.3V +5V VCC-3.3V 9. Support GND GND R1 470 MikroElektronika offers free tech support (www.mikroe.com/support) until the end of the products lifetime, so if something goes wrong, were ready and willing to help 6. Dimensions 7. HMI click boards 10. Disclaimer MikroElektronika assumes no responsibility Touchpad click is just one of several input mm mils devices on click boards. For the entire or liability for any errors or inaccuracies selection, visit: that may appear in the present document. LENGTH 42.9 1690 Specification and information contained in WIDTH 25.4 1000 www.mikroe.com/click the present schematic are subject to change HEIGHT* 3.9 154 at any time without notice. 42.9 mm / 1690 mils * without headers Copyright 2015 MikroElektronika. All rights reserved. INT 8 28 RX10 INT RX10 25.4 mm / 1000 mils 9 27 RX9 SYNC RST RX14 10 26 RST RX14 NC SCL 11 25 SCL NC 12 24 SDA SDA NC RX0 13 23 RX8 RX0 RX8 RX1 14 22 RX7 RX1 RX7