Hand Crimp Tool for Micro-Fit Terminals Order Number 200218-5900 Application Tooling Specification TYPE 4D FEATURES A full-cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping A precision user-friendly terminal locator holds terminals in the proper crimping position Right- or left-handed operation Dies and locator from this tool can be used in the Battery Powered Tool Order No. 63816-0270 (110 V) or 63816-0280 (220 V), with the use of the 63816-0800 Crimp Head This tool is IPC/WHMA-A-620 Class 2 compliant, as indicated on page 2 SCOPE Products: Micro-Fit + Female and Micro-Fit TPA Male Crimp Terminals, 24 AWG, UL1007 and UL1061 wires. Insulation Diameter Terminal Terminal Order No. Wire Size Strip Length IPC/WHMA-A-620 (1) Terminal (2) Series No. Reel Loose AWG mm In. mm In. mm In. 206460 206460-0021* 43031 43031-5003 43031-5013 43031-5004 43031-5014 24 1.12-1.58 .044-.062 0.90-1.85 .035-.073 2.50-2.90 .098-.114 43031-5005 43031-5015 43031-5006 43031-5016 (1) To achieve optimum IPC/WHMA-A-620 insulation crimps, use this insulation OD range. (2) Overall insulation OD specification for terminal. * Not available in loose-piece. Cut terminal from reel with 0.15mm max cut-off tab. DEFINITION OF TERMS BEND UP BRUSH CONDUCTOR BELL MOUTH CRIMP INSULATION ROLL CRIMP SEE NOTE TWIST STRIP BEND LENGTH DOWN CRIMP HEIGHT Doc. No: 2002185900 Release Date: 12-04-18 UNCONTROLLED COPY Page 1 of 8 Revision: A Revision Date: 12-04-18 Hand Crimp Tool for Micro-Fit Terminals OVERLAP FORM Insulation Crimp Note PUNCH GEOMETRY Due to the terminals insulation grip design or insulation diameter range, this tool uses overlap form geometry in the insulation punch. This OVERLAP produces an overlap insulation crimp (A-620- INSULATION compliant). Although the insulation punch profile CRIMP may appear lopsided, this is a normal condition for this tool. See figure to the right. Some tools with multiple crimp pockets may not have the overlap profile on all pockets. WIRE ANVIL CONDITIONS After crimping, the crimped profile should measure as follows: Conductor Crimp Wire Size Terminal Series No. Height Width AWG mm In. mm In. 206460 24 0.79-0.84 .031-.033 1.35-1.45 .053-.057 43031 Insulation Crimp Pull Force Profile Wire Size Terminal Series No. Height (Ref.) Width (Ref.) Minimum A B C D AWG mm In. mm In. N Lb. 24 24 24 24 1.85-1.95 .073-.077 1.55-1.65 .061-.065 X 206460 1.80-1.95 .071-.077 1.50-1.60 .059-.063 X 24 28.5 6.4 1.85-1.95 .073-.077 1.55-1.65 .061-.065 X 43031 1.80-1.95 .071-.077 1.50-1.60 .059-.063 X To achieve IPC/WHMA-A-620 Class 2 Crimps, the following overall wire insulation diameter ranges are recommended: Profile A: 1.12-1.40mm (.044-.055) or UL1061 Profile C: 1.28-1.58mm (.050-.077) or UL1007 Profile B: 1.28-1.58mm (.050-.077) or UL1007 Profile D: 1.12-1.40mm (.044-.055) or UL1061 Crimp attribute specifications: Wire Size Bell Mouth Brush Terminal Bend Bend Up Twist Roll Series No. Down AWG mm In. mm In. 206460 24 0.05-0.35 .002-.014 0-0.80 0-.031 8 8 6 10 43031 Tool Qualification Notes 1. (Ref) means that the dimension provided is approximate because of the wide range of wires, conductor stranding, insulation diameter and insulation hardness. 2. An occasional conductor crimp height measurement should be performed. It must lie between the minimum and maximum crimp height specification. 3. Pull force should be measured with no influence from the insulation crimp. To ensure this, strip the wire long enough so the terminal insulation grips do not contact the wire insulation. Doc. No: 2002185900 Release Date: 12-04-18 UNCONTROLLED COPY Page 2 of 8 Revision: A Revision Date: 12-04-18