638084570 Molex

FA2 Crimp Applicator for CTX50 Receptacle Terminal Unsealed Order Number 63808-4500 Application Tooling Specification FEATURES Applicator designed to industry-standard mounting and 135.80mm (5.346 ) shut height Quick setup time plus, the crimp height, track and feed adjustments can be set without removing the applicator from the press Fine adjustment allows users to achieve target with little effort by adjusting in increments of .015mm (.0006 ) for conductor crimp height and .025mm (.001 ) for insulation height Fine adjustment of the bend is achieved using the bend adjust dial Independent adjustment rings allow users to quickly adjust the conductor or insulation crimp height without affecting each other Directly adapts to most automatic wire processing machines SCOPE 2 Products: CTX50 Receptacle Terminal Unsealed, 0.35mm . Wire Size Insulation Diameter Strip Length (Ref) Terminal Order Terminal Series No. Wire Type 2 No. AWG mm mm In. mm In. FLR2X A3ZH 0.35 1.10-1.40 .043-.055 3.10 .122 UL10086 1.10-1.40 .043-.055 3.10 .122 560023-0548 UL10316 22 1.10-1.30 .043-.051 3.10 .122 UL10588 1.10-1.27 .043-.050 3.10 .122 FLR2X A3ZH 560023 A3Z 0.35 1.10-1.40 .043-.055 3.10 .122 FTP: 00949 10 00766 560023-0448 FLR13Y-A 560023-0648 UL10086 1.10-1.40 .043-.055 3.10 .122 UL10316 22 1.10-1.30 .043-.051 3.10 .122 UL10588 1.10-1.27 .043-.050 3.10 .122 CAUTION: This applicator was designed for use in a wire processor only. Doc. No: ATS-638084500 Release Date: 11-21-17 UNCONTROLLED COPY Page 1 of 8 Revision: D Revision Date: 09-20-18 FA2 Crimp Applicator for CTX50 Receptacle Terminal Unsealed DEFINITION OF TERMS CRIMP/TRANSITION 1 0 L K 9 K L SECTION K-K SECTION L-L CRIMP SPECIFICATIONS The following crimp specifications are based on document AS-560023-001 Rev J: Feature Requirement 1. Bend Up 1 Max 2. Bend Down 1 Max 3. Twist 2 Max 4. Bell Mouth Rear 0.60-0.80mm (.024-.031) 5. Bell Mouth Front None 0.55mm (.022) Max 6. Conductor Brush Not to extend above conductor crimp/transition height 7. Cut-Off Tab 0.30mm (.012) Max Wire Type Wire Size 8. Crimp Height 9. Crimp Width FLR2X A3ZH A3Z 0.35 mm 0.65-0.69mm .026-.027 in. FTP: 00949 10 00766 Conductor Crimp FLR13Y-A 1.01-1.07mm .040-.042 in. UL10086 0.63-0.67mm .025-.026 in. UL10316 22 AWG 0.69-0.73mm .027-.028 in. UL10588 0.63-0.67mm .025-.026 in. Wire Type Wire Size 10. Crimp Height 11. Crimp Width FLR2X A3ZH A3Z 0.35 mm FTP: 00949 10 00766 Insulation Crimp FLR13Y-A 1.48-1.58mm .058-.062 in. 1.33-1.43mm .052-.056 in. UL10086 UL10316 22 AWG UL10588 Doc. No: ATS-638084500 Release Date: 11-21-17 UNCONTROLLED COPY Page 2 of 8 Revision: D Revision Date: 09-20-18