BNX005-01 Murata

Spec. No. JENF243H-0006H-01 P 1/ 7 Reference Only Block Type EMIFIL BNX005-01 Reference Specification 1. Scope This reference specification applies to Block Type EMIFIL. 2. Rating 2.1 Customer Part Number 2.2 Murata Part Number BNX005-01 2.3 Rated Voltage 50 V(DC) 2.4 Test Voltage 125 V(DC) 2.5 Rated Current 15 A(DC) 2.6 Insulation Resistance 100 M min. 2.7 Voltage Drop 30 mV max. 1 MHz to 1 GHz : 40dB min. 2.8 Insertion Loss Line impedance = 50 2.9 Equivalent Circuits See the item 4 2.10 Operating Temperature - 30 C ~ + 85 C 2.11 Storage Temperature - 40 C ~ + 85 C 3. Standard Testing Condition <Unless otherwise specified> <In case of doubt> Temperature : Ordinary Temp. 15 C to 35 C Temperature : 20 C 2 C Humidity : Ordinary Humidity 25 %(RH) to 85 %(RH) Humidity : 60 %(RH) to 70 %(RH) Atmospheric pressure : 86 kPa to 106 kPa 4. Style and Dimensions 11.00.5 12.00.5 1.0 1.0 1.0 0.1 0.8 0.1 0.6 0.2 0.2 0.2 0.2 0.2 2.5 2.5 2.5 2.5 2.5 7.50.2 Note) Although some part of the product surface seems to be white in some cases, do not care because it is the result of waxing process for humidity resistance improvement. This wax does not make bad affection to mechanical or electrical performance, reliability of the product. TERMINAL LAYOUT (BOTTOM FIGURE) DIMENSIONS OF INSTALLATION HOLES (front view) 1.2 (4) CG CB (2) (PSG) (B) CG CG (CG) (CG) (3) PSG B (1) (CG) (CB) 2.50.1 5.00.1 7.50.1 (in mm) MURATA MFG CO.,LTD. 3.51.0 13.5 max. 5.00.5 18.5 max. 2.50.1 2.50.1 Spec. No. JENF243H-0006H-01 P 2/ 7 Reference Only EQUIVALENT CIRCUIT L1 L3 C2 (2) CB (1) B C1 L2 Unit Mass (Typical value) CG (4) (3) PSG 3.3g (1) ~ (4) : Terminal 5. Marking Murata mark Filter shall be marked as follows. BNX005-01 Part Number Manufacturing Date (Ex.) 59 5 1995 (Last digit of the year) 9 September Jan. to Sept. 1 ~ 9 Oct.:O,Nov.:N,Dec,:D 6. Electrical Performance No. Item Specification Test Method 6.1 Insulation Meet item 2.6. Measured at DC rated voltage between terminal Resistance (1)(2) and (3)(4). Time : 1 minute Suitable resistor : 1M. 6.2 Dielectric Filter shall be no failure. Test voltage shall be applied between terminal Strength (1)(2) and terminal (3)(4). Time : 1 to 5 seconds. Charging current : 50 mA max. 6.3 Voltage Meet item 2.7. Rated Current : 15 A Drop (1) A (2) Specimen V (3) (4) 6.4 Insertion Meet item 2.8. 50 50 Loss 10dB Balun (1) (2) 10dB Attenuator Attenuator Specimen (3) 50 (4) E 50 SG Method of measurement based on MIL-STD-220 Insertion Loss = 20log (E / E ) 0 1 : Level without FILTER (short) 0 : Level with FILTER 7. Mechanical Performance No. Item Specification Test Method 7.1 Appearance and Meet item 4. Visual Inspection and measured with Slide Dimensions Calipers. 7.2 Marking Marking is able to be read easily. It is inspected Visually. MURATA MFG CO.,LTD.