EKDMGN04-KIT Murata

Reference Only Spec. No. JENF243E-0002S-01 P1 / 8 Chip EMIFIL LC Combined Type for Large Current NFE31PT 1E9 Reference Specification 1. Scope This reference specification applies to Chip EMIFIL LC Combined Type for Large Current NFE31P Series. 2. Part Numbering NF E 31 PT 220 R 1E 9 L Product ID Structure Dimension Features Capacitance Characteristics Rated Electrode Packaging (L W) Voltage Code (L: Taping / B: Bulk) 3. Rating Customer Murata Rated Withstanding Rated Insulation Capacitance Part Number Part Number Voltage Voltage Current Resistance NFE31PT220R1E9L 22pF 30% NFE31PT220R1E9B NFE31PT470C1E9L 47pF % NFE31PT470C1E9B NFE31PT101C1E9L 100pF % NFE31PT101C1E9B NFE31PT221D1E9L 25 V 62.5 V 6 A 1000 M 220pF % (DC) (DC) (DC) min. NFE31PT221D1E9B NFE31PT471F1E9L 470pF % NFE31PT471F1E9B NFE31PT152Z1E9L 1500pF % NFE31PT152Z1E9B NFE31PT222Z1E9L 2200pF 50% NFE31PT222Z1E9B Operating Temperature: - 40 C to + 85 C Storage Temperature: - 55 C to + 125 C 4. Standard Testing Condition <Unless otherwise specified> <In case of doubt> Temperature: Ordinary Temp. 15 C to 35 C Temperature: 20 C 2 C Humidity: Ordinary Humidity 25 %(RH) to 85 %(RH) Humidity: 60 %(RH) to 70 %(RH) Atmospheric pressure: 86kPa to 106kPa 5. Style and Dimensions 0.70.2 1.00.2 0.70.2 Equivalent Circuit (1) (2) (3) Input Output (1) (3) GND 3.20.35 1.60.15 (2) (in mm) (1),(3):No Polarity Unit Mass (Typical value) 0.034g Note : Gap and bend between ceramic capacitor( 1) and ferrite bead( 2) may come out as illustrated below, however, these are not affect the performance, mounting and reliability of the products. 0.3 max. 2 1 1 2 (in mm) 0.1max. MURATA MFG. CO., LTD. 1.60.15 1.60.15Reference Only Spec. No. JENF243E-0002S-01 P2 / 8 Insertion Loss Characteristics (I.L.) (Typ.) 6. Marking No marking 7. Electrical Performance No. Item Specification Test Method Table 1 7.1 Capacitance Meet item 3. Capacitance Voltage Frequency 22 (pF) 1 to 5 V(rms) 1MHz 10% 47,100,220,470 10.2 V(rms) 1kHz 10% 1500 (pF) 2200 (pF) 0.1 V(rms) max. 1kHz 10% 7.2 Insulation Voltage : 25 V(DC) Resistance(I.R.) Time : 605 seconds 7.3 Withstanding Products shall not be damaged. Test Voltage : 62.5 V(DC) Voltage Testing Time : 1 to 5 seconds Limit the charging current: 10mA max. 8. Mechanical Performance No. Item Specification Test Method 8.1 Appearance and Meet item 5. Visual Inspection and measured with Slide Dimensions Calipers 8.2 Solderability The electrodes shall be at least 75% Flux : Ethanol solution of rosin, 25(wt)% Pre-heat : 150 10 C, 60 ~ 90 s covered with new solder coating. Solder : Sn-3.0Ag-0.5Cu Solder Temperature : 240 3 C Immersion Time : 3 1 s Immersion and emersion rates : 25mm / s Flux : Ethanol solution of rosin, 25(wt)% 8.3 Resistance to Meet Table 2. Pre-heat : 150 10 C, 60 ~ 90 s soldering heat Table 2 Solder : Sn-3.0Ag-0.5Cu Appearance No damaged Solder Temperature : 270 5 C (for NFE31PT152Z1E9 : 2505C) 22,47,100 within Immersion Time : 10 1 s 220 (pF) 15% Cap. Change Immersion and emersion rates : 25mm / s 470,1500 within Then measured after exposure the room 2200 (pF) 30% condition for 4 to 48 hours. I.R. meet item 3 Withstanding No damaged Voltage MURATA MFG. CO., LTD.