High Q and High Power Chip Multilayer Ceramic Capacitors for General Purpose
GQM22M5C2H1R6CB01_ (1111, C0G:EIA, 1.6pF, DC500V)
_: packaging code Reference Sheet
1.Scope
This product specification is applied to High Q and High Power Chip Multilayer Ceramic Capacitors used for General Electronic equipment.
2.MURATA Part NO. System
(Ex.)
GQM 22 M 5C 2H 1R6 C B01 L
(1)L/W (2)T
(3)Temperature (4)Rated (5)Nominal (6)Capacitance (7)Muratas Control
(8)Packaging Code
Dimensions Dimensions
Characteristics Voltage Capacitance Tolerance Code
3. Type & Dimensions
(Unit:mm)
(1)-1 L (1)-2 W (2) T e g
2.80.5 2.80.4 1.150.2 0.3 min. 1.0 min.
4.Rated value
(3) Temperature Characteristics
Specifications and Test
(4) (6)
(Public STD Code):C0G(EIA)
(5) Nominal Methods
Rated Capacitance
Temp. coeff Temp. Range Capacitance (Operating
Voltage Tolerance
Temp. Range)
orCap. Change (Ref.Temp.)
25 to 125 C
030 ppm/C DC 500 V 1.6 pF 0.25 pF -55 to 125 C
(25 C)
Soldering Method
Reflow
5.Package
mark (8) Packaging Packaging Unit
f180mm Reel
L 1000 pcs./Reel
EMBOSSED W8P4
f330mm Reel
K 4000 pcs./Reel
EMBOSSED W8P4
Product specifications in this catalog are as of Jun.6,2017,and are subject to change or obsolescence without notice.
Please consult the approval sheet before ordering.
Please read rating and !Cautions first.
GQM22M5C2H1R6CB01-01 1 Specifications and Test Methods
Test Method
No Item Specification
(Ref. Standard:JIS C 5101, IEC60384
1 Rated Voltage Shown in Rated value. The rated voltage is defined as the maximum voltage
which may be applied continuously to the capacitor.
When AC voltage is superimposed on DC voltage,
P-P O-P
V or V , whichever is larger, should be maintained
within the rated voltage range.
2 Appearance No defects or abnormalities. Visual inspection.
3 Dimension Within the specified dimensions. Using Measuring instrument of dimension.
4 Voltage proof No defects or abnormalities. Measurement Point : Between the terminations
Test Voltage : 250% of the rated voltage
Applied Time : 1s to 5 s
Charge/discharge current : 50mA max.
5 Insulation Resistance(I.R.) More than 10,000M Measurement Point : Between the terminations
Measurement Voltage : DC Rated Voltage
Charging Time : 2 min
Charge/discharge current : 50mA max.
Measurement Temperature : Room Temperature
6 Capacitance
Shown in Rated value. Measurement Temperature : Room Temperature
Capacitance Frequency Voltage
7 Q 30pF and over : Q 1400
C1000pF 1.0+/-0.1MHz 0.5 to 5.0Vrms
30pF and below : Q 800+20C
C:Nominal Capacitance(pF)
8 Temperature Characteristics Nominal values of the temperature coefficient is shown in The capacitance change should be measured after 5 min
of Capacitance Rated value. at each specified temp. stage.
But,the Capacitance Change under 25 is shown in Table A. Capacitance value as a reference is the value in step 3.
Capacitance Drift The capacitance drift is calculated by dividing the differences
Within +/-0.2% or +/-0.05pF between the maximum and minimum measured values in the
(Whichever is larger.) step 1,3 and 5 by the cap. value in step 3.
Step Temperature(C)
1 Reference Temp.+/-2
2 Min. Operating Temp.+/-3
3 Reference Temp.+/-2
4 Max. Operating Temp.+/-3
5 Reference Temp.+/-2
9 Adhesive Strength No removal of the terminations or other defect Solder the capacitor on the test substrate shown in Fig.3.
of Termination should occur.
Applied Force : 10N
Holding Time : 10+/-1s
Applied Direction : In parallel with the test substrate and vertical with
the capacitor side.
10 Vibration
Appearance No defects or abnormalities. Solder the capacitor on the test substrate shown in Fig.3.
Capacitance Within the specified initial value. Kind of Vibration : A simple harmonic motion
10Hz to 55Hz to 10Hz (1min)
Q Within the specified initial value. Total amplitude : 1.5mm
This motion should be applied for a period of 2h in each 3 mutually
perpendicular directions(total of 6h).
11 Substrate Appearance No defects or abnormalities. Solder the capacitor on the test substrate shown in Fig.1.
Bending test
Capacitance Within +/-5% or +/-0.5pF Pressurization method : Shown in Fig.2
Change (Whichever is larger) Flexure : 1mm
Holding Time : 5+/-1s
Soldering Method : Reflow soldering
12 Solderability 95% of the terminations is to be soldered evenly and continuously. Test Method : Solder bath method
Flux: Solution of rosin ethanol 25(mass)%
Preheat : 80 to 120 for 10s to 30s
Solder : Sn-3.0Ag-0.5Cu
Solder Temp. : 245+/-5
Immersion time :
2+/-0.5s
JEMCNS-0026A 2