Inductors (Coils) for Power Lines 11 Data Sheet LQH3NPN G0 Series 1212/3030 (inch/mm) Wound Thickness (Shield) General RoHS 1.0mm Reflow max. OK c Dimensions c Packaging Code Packaging Minimum Quantity Polarity Marking L 180mm Embossed Taping 1500 K 330mm Embossed Taping 6000 2.70.2 3.00.2 0.90.2 0.90.2 (in mm) 1.20.2 c Rated Value (p: packaging code) Inductance Rated Current Rated Current Self-Resonance Part Number Inductance DC Resistance Test Frequency (Based on Inductance Change) (Based on Temperature Rise) Frequency (min.) LQH3NPN1R0NG0p 1.0H 30% 1MHz 1650mA 1525mA 0.08 20% 160MHz LQH3NPN1R5NG0p 1.5H 30% 1MHz 1300mA 1470mA 0.10 20% 130MHz LQH3NPN2R2NG0p 2.2H 30% 1MHz 1250mA 1270mA 0.14 20% 100MHz LQH3NPN3R3NG0p 3.3H 30% 1MHz 850mA 1130mA 0.18 20% 75MHz LQH3NPN4R7NG0p 4.7H 30% 1MHz 800mA 925mA 0.26 20% 60MHz LQH3NPN6R8NG0p 6.8H 30% 1MHz 650mA 710mA 0.45 20% 48MHz LQH3NPN100MG0p 10H 20% 1MHz 500mA 630mA 0.57 20% 45MHz LQH3NPN100NG0p 10H 30% 1MHz 500mA 630mA 0.57 20% 45MHz LQH3NPN150NG0p 15H 30% 1MHz 370mA 475mA 0.91 20% 35MHz LQH3NPN220MG0p 22H 20% 1MHz 340mA 430mA 1.1 20% 25MHz LQH3NPN220NG0p 22H 30% 1MHz 340mA 430mA 1.1 20% 25MHz LQH3NPN330MG0p 33H 20% 1MHz 250mA 345mA 2.1 20% 24MHz LQH3NPN330NG0p 33H 30% 1MHz 250mA 345mA 2.1 20% 24MHz LQH3NPN470MG0p 47H 20% 1MHz 170mA 270mA 3.0 20% 19MHz LQH3NPN470NG0p 47H 30% 1MHz 170mA 270mA 3.0 20% 19MHz LQH3NPN680MG0p 68H 20% 1MHz 150mA 235mA 4.2 20% 16MHz LQH3NPN680NG0p 68H 30% 1MHz 150mA 235mA 4.2 20% 16MHz LQH3NPN101MG0 p 100H 20% 1MHz 140mA 165mA 8.0 20% 10MHz LQH3NPN101NG0p 100H 30% 1MHz 140mA 165mA 8.0 20% 10MHz LQH3NPN151MG0p 150H 20% 1MHz 110mA 145mA 11.0 20% 10MHz LQH3NPN151NG0p 150H 30% 1MHz 110mA 145mA 11.0 20% 10MHz LQH3NPN221MG0 p 220H 20% 1MHz 100mA 130mA 14.0 20% 8.5MHz LQH3NPN221NG0p 220H 30% 1MHz 100mA 130mA 14.0 20% 8.5MHz LQH3NPN251MG0p 250H 20% 1MHz 80mA 130mA 15.0 20% 8.0MHz LQH3NPN251NG0p 250H 30% 1MHz 80mA 130mA 15.0 20% 8.0MHz Class of Magnetic Shield: Magnetic shield of magnetic powder in resin Operating Temperature Range (Self-temperature rise is not included): -40 85 For re ow soldering only. Continued on the following page. oThis data sheet is applied for INDUCTORS (COILS) used for General Electronics equipment for your design. Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, its speci cations are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical speci cations because there is no space for detailed speci cations. Therefore, please approve our product speci cations or transact the approval sheet for product speci cations before ordering. 2014.3.10 Inductors (Coils) for Power Lines 22 Data Sheet Continued from the preceding page. c Notice (Rating) When applied rated current to the products, inductance will be within 30% of nomonal inductance value. When applied rated current to the products, temperature rise caused by self-generated heat shall be limited to 40C max. Keep the temperature (ambient temperature plus self-generation of heat) under 125C. c Inductance-Frequency Characteristics (Typ.) c Inductance-Current Characteristics (Typ.) 10000 1000 68H 250H 47H 220H 33H 150H 4.7H 22H 250H 100H 3.3H 15H 220H 68H 2.2H 1000 100 10H 1.5H 150H 47H 6.8H 1.0H 33H 100H 22H 15H 10H 100 10 6.8H 4.7H 3.3H 2.2H 10 1 1.5H 1.0H 1 0.1 0.001 0.01 0.1 1 10 100 0.1 1 10 100 1000 10000 Frequency (MHz) Current (mA) c Temperature Rise Characteristics (Typ.) 50 250H 220H 150H 2.2H 1.0H 45 100H 3.3H 6.8H 40 4.7H 1.5H 35 30 25 20 15 10H 15H 10 22H 33H 5 47H 68H 0 0 200 400 600 800 1000 1200 1400 1600 1800 Current (mA) c Caution/Notice Caution (Rating) Notice Do not use products beyond the rated current as Solderability of Tin plating termination chip might be this may create excessive heat. deteriorated when low temperature soldering pro le where peak solder temperature is below the Tin melting point is used. Please con rm the solderability of Tin plating termination chip before use. oThis data sheet is applied for INDUCTORS (COILS) used for General Electronics equipment for your design. Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, its speci cations are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical speci cations because there is no space for detailed speci cations. Therefore, please approve our product speci cations or transact the approval sheet for product speci cations before ordering. 2014.3.10