LQM2MPN1R5MG0L Murata

Spec No.: JELF243B 0022N-01 P1/9 CHIP COILS (CHIP INDUCTORS) LQM2MPNG0 REFERENCE SPECIFICATION 1. Scope This reference specification applies to chip coils (chip inductors) LQM2MPN G0 series for general electronic equipment. 2. Part Numbering (Ex.) LQ M 2M P N R47 M G 0 L Product ID Structure Dimension Application and Category Inductance Tolerance Dimension Other Packaging (L W) characteristic (T) L: taping *B: bulk *B: Bulk packing is also available. 3. Part Number and Rating Operating temperature range -55C to +125C Storage temperature range -55C to +125C DC Rated current Inductance resistance *1 (A) Self-resonant () Customer Murata frequency Part number Part number Nominal Ambient Ambient (MHz min.) Tolerance value Typ. Max. temperature temperature (%) *2 *2 ( H) 85C 125C LQM2MPNR47MG0L 0.47 M: 20 0.060 0.075 100 1.6 1.2 LQM2MPNR47NG0L 0.47 N: 30 0.060 0.075 100 1.6 1.2 LQM2MPN1R0NG0L 1.0 N: 30 0.085 0.107 60 1.4 1.0 LQM2MPN1R5MG0L 1.5 M: 20 0.11 0.138 50 1.2 0.9 LQM2MPN1R5NG0L 1.5 N: 30 0.11 0.138 50 1.2 0.9 LQM2MPN2R2MG0L 2.2 M: 20 0.11 0.138 40 1.2 0.9 LQM2MPN2R2NG0L 2.2 N: 30 0.11 0.138 40 1.2 0.9 LQM2MPN3R3NG0L 3.3 N: 30 0.12 0.15 30 1.2 0.9 LQM2MPN4R7MG0L 4.7 M: 20 0.14 0.175 20 1.1 0.8 LQM2MPN4R7NG0L 4.7 N: 30 0.14 0.175 20 1.1 0.8 *1 When rated current is applied to the products, temperature rise caused by self-generated heat shall be limited to 40C max. *2 As shown in the diagram below, derating is applied to the rated current based on the operating temperature. 4. Testing Conditions Unless otherwise specified Temperature: ordinary temperature (15C to 35C) Humidity: ordinary humidity 25% to 85% (RH) In case of doubt Temperature: 20C2C Humidity: 60% to 70% (RH) Atmospheric pressure: 86 kPa to 106 kPa MURATA MFG CO., LTD Spec No.: JELF243B 0022N-01 P2/9 5. Appearance and Dimensions Unit mass (typical value): 0.012 g 6. Marking No marking. 7. Electrical Performance No. Item Specification Test method 7.1 Inductance Meet chapter 3 ratings. Measuring equipment: Keysight 4294A or the equivalent (1 mA) Measuring frequency: 1 MHz 7.2 DC resistance Meet chapter 3 ratings. Measuring equipment: digital multimeter Measuring circuit: Measure with the product set to terminal 2 and the switch pressed (open between a and b). When setting or removing the product, press the switch to short between a and b. 7.3 Self-resonant Meet chapter 3 ratings. Measuring equipment: Keysight 4294A or the equivalent frequency 8. Mechanical Performance No. Item Specification Test method 8.1 Shear test No significant mechanical damage or no Force application direction: sign of electrode peeling off shall be observed. Applying force: 10 N Holding time: 5 s1 s MURATA MFG CO., LTD