X-On Electronics has gained recognition as a prominent supplier of NFL18SP207X1A3D EMI Filter Circuits across the USA, India, Europe, Australia, and various other global locations. NFL18SP207X1A3D EMI Filter Circuits are a product manufactured by Murata. We provide cost-effective solutions for EMI Filter Circuits, ensuring timely deliveries around the world.
We are delighted to provide the NFL18SP207X1A3D from our EMI Filter Circuits category, at competitive rates not only in the United States, Australia, and India, but also across Europe and beyond. A long established and extensive electronic component distribution network has enhanced our global reach and dependability, ensuring cost savings through prompt deliveries worldwide. Client satisfaction is at the heart of our business, where every component counts and every customer matters. Our technical service team is ready to assist you. From product selection to after-sales support, we strive to deliver a seamless and satisfying experience. Are you ready to experience the best in electronic component distribution? Contact X-ON Electronics today and discover why X-On are a preferred choice for the NFL18SP207X1A3D and other electronic components in the EMI Filter Circuits category and beyond.
Reference Only Spec. No. JENF243D-0003K-01 P1/ 8 Chip EMIFIL LC Combined Monolithic NFL18SPX1A3 Reference Specification 1. Scope This reference specification applies to Chip EMIFIL LC Combined Monolithic Type NFL18SP Series. 2. Part Numbering NF L 18 SP 157 X 1A 3 D Product ID Structure Dimension Features Cut-off Frequency Characteristics Rated Voltage Electrode Packaging Code (LW) (D : Taping / B : Bulk) 3. Rating DC Insulation Cut-off Inductance Rated Rated Withstanding Customer MURATA Capacitance Resistance Resistance Frequency (L) Voltage Current Voltage Part Number Part Number pF MHz nH V(DC) mA(DC) V(DC) max. M min. NFL18SP157X1A3D 150 3420% 10020% NFL18SP157X1A3B NFL18SP207X1A3D 200 2420% 8020% 3.0 NFL18SP207X1A3B 1000 10 100 30 NFL18SP307X1A3D 300 1920% 6020% NFL18SP307X1A3B NFL18SP507X1A3D 500 1120% 3820% 2.0 NFL18SP507X1A3B Operating Temperature : -55C to +125C (Includes self-heating.) Storage Temperature : -55C to +125C 4. Standard Testing Condition < Unless otherwise specified > < In case of doubt > Temperature : Ordinary Temp. / 15 C to 35 C Temperature : 20 C 2 C Humidity : Ordinary Humidity / 25 %(RH) to 85 %(RH) Humidity : 60 %(RH) to 70 %(RH) Atmospheric pressure : 86 kPa to 106 kPa 5. Style and Dimensions 0.30.1 0.40.1 0.30.1 0.80.1 Equivalent Circuits Out put Input (1) (3) 0.2min. 0.150.1 GND 1.60.1 (2) (2) No Polarity (1) (3) :Electrode Unit Mass (Typical value) 0.004g (1) (3) (in mm) (2) 0.150.1 Insertion Loss Characteristics (I.L.) (Typ.) (50system) MURATA MFG.CO., LTD. 0.60.1Reference Only Spec. No. JENF243D-0003K-01 P2/ 8 6. Marking No marking 7. Electrical Performance No. Item Specification Test Method 7.1 Capacitance Meet item 3. Frequency : 10.1MHz (Cap.) Voltage : 10.2V(rms) Frequency : 101MHz 7.2 Inductance (L) Voltage : 10.2V(rms) 7.3 DC Resistance Measured with 10mA max. (Rdc) Measured between terminal (1)-(3). (ref. Item5) 7.4 Insulation Voltage : Rated Voltage Resistance(I.R.) Time : 1 minutes max. 7.5 Withstanding Products shall not be damaged. Test Voltage : 30V(DC) Voltage Time : 1 to 5 s Charge Current : 50 mA max. 8. Mechanical Performance No. Item Specification Test Method 8.1 Appearance and Meet item 5. Visual Inspection and measured with Slide Dimensions Calipers. 8.2 Solderability Electrodes shall be at least 90% Flux : Ethanol solution of rosin, 25(wt)% covered with new solder coating. Pre-heat : 150 10C, 60 to 90s Solder : Sn-3.0Ag-0.5Cu Solder Temperature : 240 3C Immersion Time : 31 s Immersion and emersion rates : 25mm / s 8.3 Resistance to Meet Table 1. Flux : Ethanol solution of rosin, 25(wt)% soldering heat Table 1 Pre-heat : 150 10C, 60 to 90s Solder : Sn-3.0Ag-0.5Cu Appearance No damaged Solder Temperature : 270 5C Cap. Change within 5% Immersion Time : 10 1 s L Change within 5% Immersion and emersion rates : 25mm / s I.R. meet item 3 8.4 Bending Meet Table 2. It shall be soldered on the glass-epoxy substrate Strength (t = 1.0mm). Table 2 Deflection : 2.0 mm Appearance No damaged Keeping Time : 30 s Cap. Change within 5% Pressure jig R230 F Deflection 45 45 Product (in mm) 8.5 Drop Products shall be no failure after It shall be dropped on concrete or steel board. tested. Method : Free fall Height : 1m Attitude from which the product is dropped : 3 directions The Number of Time : 3 times for each direction (Total 9 times) MURATA MFG.CO., LTD.