NFP0QSN122HL2D

Reference Only Spec No. JEFL243E-0020C-01 P1/9 Common Mode Noise Filter NFP0QSNHL2 Reference Specification 1. Scope This reference specification applies to Chip Common Mode Noise Filter NFP0QSN Series. 2. Part Numbering (ex.) NF P 0Q S N 121 H L 2 D (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (1) Chip Common Mode Noise Filter (6) Common Mode Insertion Loss Characteristic (2) Structure (P : Film Type) Resonant Frequency(Typ.) (3) Dimension (LW) 0Q : 0.650.5mm (7) Circuit H : Characteristic Impedance 100 system (4) Type (8) Features (5) Category N : General Use (9) Number of Line (10) Packaging Code D : Taping / B : Bulk 3. Rating Common Mode Insertion Loss Characteristic MURATA Customer (dB Typ.) Part Number Part Number 240 700 900 1.7 2.4 MHz MHz MHz GHz GHz NFP0QSN112HL2D 14 24 26 24 20 NFP0QSN112HL2B NFP0QSN122HL2D 12 23 26 25 21 NFP0QSN122HL2B Common Mode Impedance DC Insulation Withstanding Rated Rated ( typ.) MURATA Resistance Resistance Voltage Current Voltage at 100MHz (Rdc) Part Number (I.R.) (mA) (V(DC)) (V(DC)) (Under Standard () () Testing Condition) NFP0QSN112HL2D 90 100 5 3.030% NFP0QSN112HL2B 100M 12.5 NFP0QSN122HL2D min. 2.730% 65 100 5 NFP0QSN122HL2B Operating Temperature : -40 to +85C Storage Temperature : -40 to +85C 4. Standard Testing Conditions <Unless otherwise specified> <In case of doubt> Temperature : Ordinary Temperature 15 to 35C Temperature : 20 2C Humidity : Ordinary Humidity 25 to 85%(RH) Humidity : 60 to 70%(RH) Atmospheric Pressure : 86 to106kPa 5.Style and Dimensions (2) Equivalent Circuits (1) (Top View) (1) (2) (4) (3) (3) (4) (Side View) No polarity. Unit Mass(Typical value) 0.5mg (Bottom View) 6.Marking No Marking. MURATA MFG.CO., LTD Reference Only Spec No. JEFL243E-0020C-01 P2/9 7. Electrical Performance No. Item Specification Test Method 7.1 Meet item 3. Common Mode Measuring Frequency : 1001MHz (ref.item 10.) Impedance Measuring Equipment : Agilent 4291A or the equivalents (In case of doubt in standard condition, the heat treatment(200C, about 10 minutes)shall be applied. 7.2 Withstanding Products shall not be damaged. Test Voltage : 2.5 times for Rated Voltage Voltage Time : 1 to 5 seconds Charge Current : 1 mA max.(ref.item 10.) 7.3 Meet item 3. Measuring current : 100mA max.(ref.item 10.) DC Resistance (Rdc) 7.4 Insulation Measuring voltage : Rated Voltage Measuring time : 1 minute max. (ref.item 10.) Resistance (I.R.) 7.5 Self- temperature rise shall be limited The rated current is applies. Rated Current to 25 max. 8.Mechanical Performance No. Item Specification Test Method 8.1 Appearance and Meet item 5. Visual Inspection and measured with Slide Calipers. Dimensions 8.2 Solderability The electrodes shall be at least Flux : Ethanol solution of rosin,25(wt)% 95% covered with new solder Pre-Heating : 15010C, 6090s coating. Solder : Sn-3.0Ag-0.5Cu Solder Temperature : 2403C Immersion Time : 30.5s Immersion and emersion rates : 25 mm / s 8.3 Resistance to Meet Table 1. Flux : Ethanol solution of rosin,25(wt)% Soldering Heat Table 1 Pre-Heating : 15010C, 6090s Solder : Sn-3.0Ag-0.5Cu Appearance No damaged Solder Temperature : 2705C Common Mode Immersion Time : 51s Impedance within 20% Immersion and emersion rates : 25 mm / s Change Then measured arter exposure in the room condition I.R. 100M min. for 4 to 48 hours. 8.4 Drop It shall be dropped on concrete or steel board. DC Resistance within 30% Method : free fall Change Height : 1m The Number of Times : 10 times 8.5 Vibration It shall be soldered on the substrate. Oscillation Frequency : 10 to 2000 to 10Hz for 15 minutes Total amplitude : 3.0 mm or Acceleration amplitude 2 196 m/s whichever is smaller. Testing Time : A period of 2 hours in each of 3 mutually perpendicular directions. 8.6 Bending Meet Table 2. Substrate : (t =1.0 mm). Strength Table 2 Deflection : 3 mm Speed of Applying Force : 1.0 mm / s Appearance No damaged Keeping time : 5 seconds DC Resistance within 30% Pressure jig Change R230 F Deflection 45 45 Product MURATA MFG.CO., LTD