OKL-T/6-W5N-C

OKL-T/6-W5 Series www.murata-ps.com Programmable Output 6-Amp iLGA SMT PoLs TTypical unitypical unit FEATURES PRODUCT OVERVIEW The OKL-T/6-W5 series are non-isolated effi cient Point of Load (PoL) module features 2.4-5.5Vdc input voltage range Point-of-Load (PoL) DC/DC power converters for programmable output voltage and On/Off control. Programmable output voltage from 0.6-3.3Vdc embedded applications. Featuring inspectable Land These converters also include under voltage lock High power conversion effi ciency at 93.5% Grid Array (LGA) format, the OKL-T/6-W5 measures out (UVLO), output short circuit protection, over- Inspectable Land Grid Array only 0.48 x 0.48 x 0.283 inches max. (12.2 x 12.2 current and over temperature protections. x 7.2 mm max.). An optional sequence/tracking feature allows Drives up to 300 F ceramic capacitive loads The wide input range is 2.4 to 5.5 Volts DC. power sequencing of PoLs. These units are certi- On/Off control The maximum output current is 6 Amps. Based fied to all standard UL/EN/IEC 60950-1 safety Optional Sequence/Tracking operation on fi xed-frequency synchronous buck converter certifi cations (2nd Edition) and RoHS-6 hazardous Outstanding thermal derating performance switching topology, the high power conversion substance compliance. Over temperature and over current protection Certifi ed to UL/EN/IEC 60950-1 safety, 2nd Edition RoHS-6 hazardous substance compliance Connection Diagram +Vin +Vout Switching F1 On/Off Sense Control Filters Controller Current Sense External Trim DC Power Reference and Open = On Source Error Amplier Closed = Off (Positive On/Off) Common Common Sequence/Tracking (OKL2 Models) Figure 1. OKL-T/6-W5 Note: Murata Power Solutions strongly recommends an external input fuse, F1. See specifi cations. For full details go to www.murata-ps.com/rohs www.murata-ps.com/support MDC OKL-T/6-W5 Series.C04 Page 1 of 17OKL-T/6-W5 Series Programmable Output 6-Amp iLGA SMT PoLs PERFORMANCE SPECIFICATIONS SUMMARY AND ORDERING GUIDE Output Input PackagePinout P83 On/ Efficiency Seq/ Model Number Regulation (max.) Off Vout Iout (Amps, Power R/N (mV p-p) Vin nom. Range Iin, no load Iin, full load Case C83 Track Logic (Volts) max.) (Watts) Max. (Volts) (Volts) (mA) (Amps) inches (mm) Line Load Min. Typ. 0.48x0.48x0.283 max OKL-T/6-W5P-C 0.6-3.3 6 19.8 25 0.35% 0.35% 5 2.4-5.5 25 4.24 91.5% 93.5% Pos. no (12.2x12.2x7.2) max 0.48x0.48x0.283 max OKL-T/6-W5N-C 0.6-3.3 6 19.8 25 0.35% 0.35% 5 2.4-5.5 25 4.24 91.5% 93.5% Neg. no (12.2x12.2x7.2) max 0.48x0.48x0.283 max OKL2-T/6-W5P-C 0.6-3.3 6 19.8 25 0.35% 0.35% 5 2.4-5.5 25 4.24 91.5% 93.5% Pos. yes (12.2x12.2x7.2) max 0.48x0.48x0.283 max OKL2-T/6-W5N-C 0.6-3.3 6 19.8 25 0.35% 0.35% 5 2.4-5.5 25 4.24 91.5% 93.5% Neg. yes (12.2x12.2x7.2) max I/O caps are necessary for our test equipment and may not be needed for your application. The output range (50% load) is limited by Vin. See detailed specs for full conditions. Use adequate ground plane and copper thickness adjacent to the converter. All specifications are a t nominal line voltage, Vout=nominal (3.3V for W5 models) and full load, +25 deg.C. unless otherwise noted. Ripple and Noise (R/N) are shown at Vout=1V. See specs for details. Output capacitors are 10 F ceramic. Input cap is 22 F. See detailed specifications. No load input current is shown at Vout = 3.3V. PART NUMBER STRUCTURE OK L 2 - T / 6 - W5 N - C Non-isolated PoL LGA Surface Mount Sequence/tracking RoHS Hazardous Blank = Not installed Substance Compliance 2 = Installed C = RoHS-6 (does not claim EU RoHS exemption 7blead in solder) Trimmable Output Voltage Range On/Off Logic 0.6-3.3Vdc P = Positive Logic N = Negative Logic Maximum Rated Output Input Voltage Range Current in Amps 2.4-5.5Vdc Product Label Because of the small size of these products, the product label contains a Model Number Product Code OKL-T/6-W5P-C L01006 character-reduced code to indicate the model number and manufacturing date OKL-T/6-W5N-C L00006 code. Not all items on the label are always used. Please note that the label OKL2-T/6-W5P-C L21006 differs from the product photograph. Here is the layout of the label: OKL2-T/6-W5N-C L20006 The manufacturing date code is four characters: XXXXXX Product code First character Last digit of manufacturing year, example 2009 Mfg. date YMDX Rev. Revision level Second character Month code (1 through 9 = Jan-Sep code O, N, D = Oct, Nov, Dec) Figure 2. Label Artwork Layout Third character Day code (1 through 9 = 1 to 9, 10 = 0 and 11 through 31 = A through Z) The label contains three rows of information: Fourth character Manufacturing information First row Murata Power Solutions logo Second row Model number product code (see table) Third row Manufacturing date code and revision level www.murata-ps.com/support MDC OKL-T/6-W5 Series.C04 Page 2 of 17