AEC-Q200 RoHS Compliance This component is compliant with RoHS directive. This component was always RoHS compliant from the first date of manufacture. SF2039B-2 Designed for SDARS IF Receiver Low Insertion Loss 5.0 X 7.0 mm Surface-Mount Case 72.540 MHz Differential or Single Ended Input and Output Pb Complies with Directive 2011/65/EU (RoHS) SAW Filter Absolute Maximum Ratings Rating Value Units Maximum Incident Power in Passband +10 dBm Max. DC voltage between any 2 terminals 30 VDC Storage Temperature Range (with tape & reel) -40 to +85 C Storage Temperature Range (without tape & reel) -50 to +125 C Max Soldering Profile 265C for 10 s SMP-03 Electrical Characteristics Characteristic Sym Notes Min Typ Max Units Nominal Center Frequency f 72.540 MHz C 1 Passband Insertion Loss IL 10.5 12.5 dB 1dB Passband BW 3.7 4.0 MHz 1 15dB Bandwidth BW 6.5 6.7 MHz 15 30dB Bandwidth BW 1 7.5 7.7 MHz 30 Amplitude Ripple over fc 1.85 MHz 0.5 1.3 dB P-P Group Delay Variation over fc 1.85 MHz GDV 60 150 ns P-P Rejection 50 to 66.48 MHz 40 47 66.48 to 68.08 MHz 30.5 43 77.30 to 78.60 MHz 38 42 1, 3 dB 78.60 to 86.50 MHz 40 44 86.50 to 91.50 MHz 45 50 91.50 to 100.00 MHz 45 55 Operating Temperature Range T 1 -40 +105 C A Frequency Temperature Coefficient FTC -18 ppm/C Differential Input 175 ohms Differential Output 1000 ohms Case Style SMP-03 7 x 5 mm Nominal Footprint 6 Lid Symbolization (YY=year, WW=week, S=shift) See note 4 RFM SF2039B YYWWS Electrical Connections Connection Terminals Port 1 Hot 10 Port 1 Ground Return 1 Port 2 Hot 5 Port 2 Ground Return 6 Case Ground All Others Copyright Murata Manufacturing Co., Ltd. All rights reserved. March 2014 SF2039B-2 (R) 8/24/18 Page 1 of 7 www.murata.comCAUTION: Electrostatic Sensitive Device. Observe precautions for handling. NOTES: 1. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 and measured with 50 network analyzer. 2. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. 3. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. 4.LRI or after the part number indicateslow rate initial productio andEN or indicatesengineering prototypes 5. The design, manufacturing process, and specifications of this filter are subject to change. 6. Tape and Reel Standard ANSI / EIA 481. 7. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design. 8. US and international patents may apply. 9. Murata, stylized Murata logo, and Murata N.A., Inc. are registered trademarks of Murata Manufacturing Co., Ltd. Matching Circuit and Matching Component Values Used in G3 Sirius Radios (Refer to Sirius Radio G3 Chipset Application Note, Doc. RX000104-B, Sec. 4.2.3) SF2039B-2 TDM1 Narrowband SAW Matching Circuit TDM1 Narrowband SAW Matching Values Reference Designator Value C5 10 pF C6 10 pF L3 330 nH L4 560 nH C7 100 pF C8 100 pF Copyright Murata Manufacturing Co., Ltd. All rights reserved. March 2014 SF2039B-2 (R) 8/24/18 Page 2 of 7 www.murata.com