F981A106MMA

SOLID TANTALUM ELECTROLYTIC CAPACITORS Resin-molded Chip, High Capacitance Series F98 Specifications Compliant to the RoHS directive (2002/95/EC). Item Performance Characteristics Category --55 to +125C (Rated temperature : +85C) Temperature Range Capacitance Tolerance 20 (at 120Hz) % Dissipation Factor Refer to the table below ESR Refer to the table below Refer to the table below Provided that After 5 minute s application of rated voltage, leakage current at 85C, Leakage Current 10 times or less than 20C specified value. After 5 minute s application of rated voltage, leakage current at 125C, 12.5 times or less than 20C specified value. At 40C, 90 to 95% R.H., For 500hours (No voltage applied) Damp Heat Capacitance Change Refer to the table below (* 1) (Steady State) Dissipation Factor 150% or less of initial specified value Leakage Current 200% or less of initial specified value Applications At --55C / +125C, For 30 minutes each, 5 cycles Smartphone Wireless module Capacitance Change Refer to the table below (* 1) Temperature Cycles Mobile phone Hearing aid Dissipation Factor 150% or less than the initial specified value Leakage Current Initial specified value or less Type numbering system (Example : 6.3V 10F) 10 seconds reflow at 260C, 5 seconds immersion at 260C 1 2 3 4 5 6 7 8 9 10 11 Resistance to Soldering Capacitance Change Refer to the table below (* 1) Taping code Heat Leakage Current Initial specified value or less F 9 8 0 J 1 0 6 M M (Refer to page 333 for details) Leakage Current Initial specified value or less Case code After application of surge in series with a 1k resistor at the Capacitance tolerance rate of 30 seconds ON, 30 seconds OFF, for 1000 successive Rated capacitance C test cycles at 85 , capacitors shall meet the characteristic Rated voltage requirements listed below. Surge Series Capacitance Change Refer to the table below (* 1) Drawing Dissipation Factor 150% or less than the initial specified value Leakage Current 200% or less than the initial specified value L W1 After 1000 hours application of rated voltage in series with a 3 resistor at 85C, capacitors shall meet the characteristic requirements table below H Endurance Capacitance Change Refer to the table below (* 1) Dissipation Factor 150% or less than the initial specified value Leakage Current 200% or less than the initial specified value After applying the pressure load of 5N W2 for 101 seconds horizontally to the center of capacitor side body which has no electrode and has been soldered Shear Test 5N (0.51kg f) beforehand on a substrate, there shall be S1 S2 S1 found neither exfoliation For 10 1 seconds nor its sign at the terminal electrode. (mm) Keeping a capacitor surface-mounted on a substrate upside Case Code L W1 W2 H S1 S2 down and supporting the substrate at both of the opposite bottom points 45mm apart from the center of capacitor, the U 1.10 0.05 0.60 0.05 0.35 0.05 0.55 0.05 0.3 0.05 0.5 0.05 pressure strength is applied with + + 0.2 0.2 a specified jig at the center of the 20 M 1.6 0.85 0.65 0.1 0.8 0.1 0.5 0.1 0.6 0.1 -0.1 -0.1 R230 Terminal Strength substrate so that substrate +0.2 +0.2 S 2.0 1.25 0.9 0.1 0.8 0.1 0.5 0.1 1.0 0.1 may bend by 1mm as illustrated. -0.1 -0.1 Then, there shall be found no remarkable abnormality on the 45 45 capacitor terminals. Marking Capacitance code U Case M Case S Case As for the surge voltage, refer to page 332 for details. J Js Rated *2 Leakage Disspation Case ESR *1 C/C Rated Volt Capacitance Part Number Current Factor code (%) ( 100kHz) (F) (% 120Hz) (A) Rated voltage Rated voltage F980G475MUA 4.7 U 0.5 20 20 30 (Voltage code) (Voltage code) F980G106MUA 0.8 25 20 10 U 30 22 M F980G226MMA 0.9 15 7.5 30 33 M F980G336MMA 1.3 30 4 30 F980G476MMA 47 M 1.9 40 8 30 4V Standard Ratings 68 M F980G686MMA 27.2 50 10 30 68 S F980G686MSA 2.7 30 4 30 V 4 6.3 10 16 20 25 Capacitance 100 M F980G107MMA 80.0 60 10 30 Cap.(F) Code 0G 0J 1A 1C 1D 1E code F980G107MSA 4 100 S 4.0 35 30 220 S F980G227MSA 132 80 5 30 1 --- 105 M M M 4.7 U F980J475MUA 0.6 20 20 30 2.2 225 U M M --- 4.7 M F980J475MMA 0.5 20 7.5 30 F980J106MMA 4.7 475 U U M (U) M M --- 10 M 0.6 8 6 30 22 F980J226MMA 1.4 20 6 M 30 6.3V 10 M M a 106 U (U) S 33 M F980J336MMA 4.2 35 8 30 47 M F980J476MMA 29.6 45 10 30 22 226 M M (M) S J F980J476MSA 47 S 3.0 25 6 30 100 S F980J107MSA 63.0 50 8 30 33 336 M M (M) S n F981A225MUA 2.2 U 0.5 15 15 30 47 S s 476 M M S F981A225MMA 0.5 6 7.5 2.2 M 30 4.7 M F981A475MMA 0.5 6 6 30 68 686 M S w 10V 10 M F981A106MMA 1.0 20 7.5 30 100 107 M S S A F981A226MSA 22 S 2.2 20 4 20 33 S F981A336MSA 3.3 30 6 30 220 J 227 S 47 S F981A476MSA 9.4 35 5 30 F981C105MMA ( ) The series in parentheses are being developed. 1 M 0.5 6 10 30 F981C225MMA 6 10 Please contact to your local Nichicon sales office when 2.2 M 0.5 30 16V 4.7 M F981C475MMA 0.8 12 12 30 these series are being designed in your application. 10 S F981C106MSA 1.6 18 4 20 20V 1 M F981D105MMA 0.5 6 10 30 We can consider the type of compliance to AEC-Q200. 25V F981E105MMA 0.5 8 10 30 1 M Please contact to your local Nichicon sales office when these series are being designed in your application. 2 : Leakage Current * After 5 minute s application of rated voltage, leakage current at 20C. CAT.8100B 1mmX-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for Nichicon manufacturer: Other Similar products are found below : TVX2W101MDD TVX1V681MCD TVX0J101MAD TVX1H152MCD TVX2W470MDD TVX1E330MAD UPS1H010MDD TVX2C010MAD UHE1H010MDD TVX1A470MAD UFW1H0R1MDD POLYLESR-KIT POLYLL-KIT LAR2E821MELC30 LGU1H272MELZ LGX2H560MELZ25 LNC2G392MSEG LNC2G472MSEH LNC2G682MSEG LNC2V682MSEH LNK2G122MSEF LNK2G182MSEF LNK2V182MSEF LNR1J104MSE LNR1K683MSE LNR1V105MSE LNR2A103MSE LNR2A153MSE LNR2C103MSE LNR2D152MSE LNT1C105MSE LNT1E154MSE LNT1E474MSE LNT1J103MSE LNT2A223MSE LNT2G152MSEF LNT2H222MSEG LNT2W681MSEF LNU2G562MSEH LNX2H182MSEG LNX2V273MSEK LNX2W222MSEH LNX2W562MSEJ LNY2G182MSEG LNY2G222MSEF LNY2V152MSEF LNY2W182MSEG LQR2G182MSEF LQR2G562MSEH LQR2W472MSEG