CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS Chip Type, LongLife Assurance PCG PCS Dimensions Leakage Current Rated Voltage ESR Rated Ripple Load life of 5000 hours at 105C. Surge Voltage Rated Capacitance Case Size (A) (V) (m) (mArms) tan Part Number SMD type : Lead free reflow soldering condition at (V) (F) D L (mm) at 20 after (code) () (20C/100kHz) (105C/100kHz) 2 minutes 260C peak correspondence. 220 5 6 0.12 110 30 2100 PCG0E221MCL1GS Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). AEC-Q200 compliant. Please contact us for details. 330 5 6 0.12 500 30 2200 PCG0E331MCL1GS 330 5 6 0.12 500 10 3300 PCG0E331MCO1GS Long Life Long Life PCL PCF PCS 470 6.3 6 0.12 235 20 2900 PCG0E471MCL1GS Specifications 560 6.3 6 0.12 280 20 3000 PCG0E561MCL1GS 2.5 2.8 (0E) Item Performance Characteristics 820 8 7 0.12 410 20 3300 PCG0E821MCL1GS Category Temperature Range 55 to +105C 1500 10 8 0.12 750 17 4100 PCG0E152MCL1GS Rated Voltage Range 4 to 16V 2700 10 10 0.12 1350 12 4700 PCG0E272MCL1GS Rated Capacitance Range 22 to 560F 3300 10 12.7 0.12 1650 10 5500 PCG0E332MCL1GS Capacitance Tolerance 20% at 120Hz, 20C 4700 10 12.7 0.12 2350 10 5600 PCG0E472MCL1GS Tangent of loss angle (tan ) Less than or equal to the specified value at 120Hz, 20C ( 1) ESR Less than or equal to the specified value at 100kHz, 20C 180 5 6 0.12 144 32 1900 PCG0G181MCL1GS Leakage Current ( 2) Less than or equal to the specified value . After 2 minutes application of rated voltage at 20C 220 5 6 0.12 300 32 2000 PCG0G221MCL1GS Temperature Characteristics Z+105C / Z+20C 1.25 (100kHz) 220 5 6 0.12 300 15 2900 PCG0G221MCO1GS Z55C / Z+20C 1.25 (Max.Impedance Ratio) 390 6.3 6 0.12 312 22 2700 PCG0G391MCL1GS 4 Within 20% of the initial capacitance value ( 3) Capacitance change 4.6 680 8 7 0.12 544 21 3200 PCG0G681MCL1GS The specifications listed at right shall be met when the (0G) tan 150% or less than the initial specified value Endurance capacitors are restored to 20C after the rated voltage is ESR ( 1) 150% or less than the initial specified value 1200 10 8 0.12 960 17 4000 PCG0G122MCL1GS applied for 5000 hours at 105C. Leakage current ( 2) Less than or equal to the initial specified value 4600 2200 10 10 0.12 1760 13 PCG0G222MCL1GS 2700 10 12.7 0.12 2160 11 5300 PCG0G272MCL1GS Capacitance change Within 20% of the initial capacitance value ( 3) The specifications listed at right shall be met when the Damp Heat tan 150% or less than the initial specified value 3300 10 12.7 0.12 2640 11 5400 PCG0G332MCL1GS capacitors are restored to 20C after the rated voltage is ESR ( 1) 150% or less than the initial specified value (Steady State) applied for 1000 hours at 60C, 90% RH. 33 1800 Leakage current ( 2) Less than or equal to the initial specified value 150 5 6 0.12 189 PCG0J151MCL1GS 180 5 6 0.12 500 33 1900 PCG0J181MCL1GS After soldering the capacitor under the soldering conditions Capacitance change Within 10% of the initial capacitance value ( 3) 180 5 6 0.12 500 17 3000 PCG0J181MCO1GS prescribed here, the capacitor shall meet the specifications listed at tan 130% or less than the initial specified value right. 0.12 340 23 2600 270 6.3 6 PCG0J271MCL1GS ESR ( 1) Pre-heating shall be done at 150 to 200C and for 60 to 180 sec. 130% or less than the initial specified value The duration for over +230C temperature at capacitor surface shall Leakage current ( 2) Less than or equal to the initial specified value 330 6.3 6 0.12 416 23 2700 PCG0J331MCL1GS 6.3 Resistance to not exceed 60 seconds. 7.2 (0J) In case peak temperature is 250C or less, reflow soldering shall be 470 8 7 0.12 592 22 3100 PCG0J471MCL1GS Soldering Heat two times maximum. 0.12 1260 18 3800 PCG0J102MCL1GS 1000 10 8 In case peak temperature is 260C or less, reflow soldering shall be once. 1800 10 10 0.12 2268 14 4400 PCG0J182MCL1GS Measurement for solder temperature profile shall be made at the capacitor top. 2200 10 12.7 0.12 2772 12 5000 PCG0J222MCL1GS Marking 2700 10 12.7 0.12 3402 12 5100 PCG0J272MCL1GS Navy blue print on the case top 1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform. 82 5 6 0.12 164 35 1700 PCG1A820MCL1GS 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120 100 5 6 0.12 250 35 1800 PCG1A101MCL1GS minutes at 105C. 3 Initial value : The value before test of examination of resistance to soldering. 150 6.3 6 0.12 300 25 2500 PCG1A151MCL1GS 180 6.3 6 0.12 360 25 2600 PCG1A181MCL1GS Type numbering system (Example : 6.3V 220F) Dimensions Positive 10 11.5 330 8 7 0.12 660 23 3100 PCG1A331MCL1GS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Plastic platform (1A) Capacitance Lot No. 0.3 MAX. C0.2 P C S 0 J 2 2 1 M C L 1 G S 560 10 8 0.12 1120 20 3600 PCG1A561MCL1GS Taping code 820 10 10 0.12 1640 15 4300 PCG1A821MCL1GS Size code 1000 10 12.7 0.12 2000 13 4800 PCG1A102MCL1GS Configuration 1500 10 12.7 0.12 3000 13 4900 PCG1A152MCL1GS Capacitance tolerance (20%) 47 5 6 0.12 150 40 1500 PCG1C470MCL1GS +0.1 L Rated capacitance (220F) Voltage ( j:6.3v) -0.4 Series H Negative 56 5 6 0.12 240 40 1600 PCG1C560MCL1GS Rated voltage (6.3V) 82 6.3 6 0.12 262 30 2300 PCG1C820MCL1GS Series name Type 100 6.3 6 0.12 320 30 2400 PCG1C101MCL1GS (mm) 16 Size 5 6L 6.3 6L 8 7L 18.4 150 8 7 0.12 480 28 2800 PCG1C151MCL1GS (1C) 5.0 6.3 8.0 D 270 10 8 0.12 864 25 3300 PCG1C271MCL1GS 5.9 5.9 6.9 L A 6.0 7.3 9.0 3700 470 10 10 0.12 1504 20 PCG1C471MCL1GS 5.3 6.6 8.3 B Voltage 680 10 12.7 0.12 2176 18 4100 PCG1C681MCL1GS Frequency coefficient of rated ripple current 5.3 6.6 8.3 C V 4 6.3 10 16 820 10 12.7 0.12 2624 18 4200 PCG1C821MCL1GS 1.6 2.1 3.2 0 Frequency0/ 120Hz 1kHz 10kHz 100kHz or more E Code g j A C 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 H Coefficient 0.05 0.30 0.70 1.00 For taping specifications, recommended land size/soldering by reflow and minimum order quantity, please refer to the Guidelines for Aluminum Electrolytic Capacitors. Dimension table in next page. CAT.8100K CS 220 j 941 D0.5 B0.2 E 0.5 MAX. A0.2CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS Chip Type, Higher Capacitance LongLife Assurance PCS PCL Dimensions Long life of 20000 hours at 105C. High reliability, Low ESR, High ripple current. Leakage Current Rated Voltage ESR Rated Ripple Surge Voltage Rated Capacitance Case Size (A) SMD type : Lead free reflow soldering condition at (V) (m) (mArms) tan Part Number (V) (F) D L (mm) at 20 after 260C peak correspondence. (code) (20C/100kHz) (105C/100kHz) () 2 minutes Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). 150 5 6 0.12 120 25 2200 PCS0G151MCL1GS AEC-Q200 compliant. Please contact us for details. 20 2800 PCS0G331MCL1GS 330 6.3 6 0.12 264 4 Long Life 4.6 PCS PCL (0G) 330 8 7 0.12 264 22 3200 PCS0G331MCL9GS 560 8 7 0.12 448 18 3600 PCS0G561MCL1GS 1600 PCS0J470MCL1GS 47 5 6 0.12 100 35 Specifications 100 5 6 0.12 126 25 2400 PCS0J101MCL1GS Item Performance Characteristics 100 6.3 6 0.12 126 22 2800 PCS0J101MCL9GS Category Temperature Range 55 to +105C 6.3 7.2 2800 PCS0J121MCL9GS 120 6.3 6 0.12 151 22 Rated Voltage Range 2.5 to 25V (0J) 220 6.3 6 0.12 277 20 2800 PCS0J221MCL1GS Rated Capacitance Range 12 to 3300F 220 8 7 0.12 277 22 3200 PCS0J221MCL9GS Capacitance Tolerance 20% at 120Hz, 20C PCS0J391MCL1GS 390 8 7 0.12 491 22 3200 Less than or equal to the specified value 120Hz, 20C Tangent of loss angle (tan ) at 33 5 6 0.12 100 40 1300 PCS1A330MCL1GS ESR ( 1) Less than or equal to the specified value at 100kHz, 20C 56 6.3 6 0.12 112 27 2300 PCS1A560MCL9GS Leakage Current ( 2) Less than or equal to the specified value . After 2 minutes application of rated voltage at 20C PCS1A680MCL1GS 68 5 6 0.12 136 30 2100 10 Temperature Characteristics Z+105C / Z+20C 1.25 (100kHz) 11.5 (1A) 120 6.3 6 0.12 240 27 2300 PCS1A121MCL1GS Z55C / Z+20C 1.25 (Max.Impedance Ratio) 150 8 7 0.12 300 30 2600 PCS1A151MCL9GS Capacitance change Within 20% of the initial capacitance value ( 3) PCS1A271MCL1GS 270 8 7 0.12 540 22 3200 The specifications listed at right shall be met when the tan 150% or less than the initial specified value Endurance capacitors are restored to 20C after the rated voltage is 22 5 6 0.12 100 45 1100 PCS1C220MCL1GS ( 1) ESR 150% or less than the initial specified value applied for 20000 hours at 105C. Leakage current ( 2) Less than or equal to the initial specified value 39 5 6 0.12 125 35 2000 PCS1C390MCL1GS 39 6.3 6 0.12 125 30 2200 PCS1C390MCL9GS 16 18.4 Capacitance change Within 20% of the initial capacitance value ( 3) (1C) 68 6.3 6 0.12 218 30 2200 PCS1C680MCL1GS The specifications listed at right shall be met when the Damp Heat tan 150% or less than the initial specified value capacitors are restored to 20C after the rated voltage is 82 8 7 0.12 262 28 2800 PCS1C820MCL9GS ESR ( 1) (Steady State) 150% or less than the initial specified value applied for 1000 hours at 60C, 90% RH. Leakage current ( 2) Less than or equal to the initial specified value 120 8 7 0.12 384 28 2800 PCS1C121MCL1GS No marked, 1 will be put at 12th digit of type numbering system. After soldering the capacitor under the soldering conditions : In this case, 9 will be put at 12th digit of type numbering system. Capacitance change Within 10% of the initial capacitance value ( 3) prescribed here, the capacitor shall meet the specifications listed at tan 130% or less than the initial specified value right. ESR ( 1) Pre-heating shall be done at 150 to 200C and for 60 to 180 sec. 130% or less than the initial specified value For taping specifications, recommended land size/soldering by The duration for over +230C temperature at capacitor surface shall Leakage current ( 2) Less than or equal to the initial specified value reflow and minimum order quantity, please refer to the Guidelines Resistance to not exceed 60 seconds. for Aluminum Electrolytic Capacitors. In case peak temperature is 250C or less, reflow soldering shall be Soldering Heat two times maximum. In case peak temperature is 260C or less, reflow soldering shall be once. Measurement for solder temperature profile shall be made at the capacitor top. Marking Navy blue print on the case top 1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120 minutes at 105C. 3 Initial value : The value before test of examination of resistance to soldering. Dimensions Type numbering system (Example : 16V 120F) Positive 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Plastic platform Capacitance Lot No. C0.2 0.3MAX. P C L 1 C 1 2 1 M C L 1 G S Taping code Size code Configuration Capacitance tolerance (20%) 5 0.3 Rated capacitance (120F) Voltage (C:16V) Series H Negative 6.3,8,10 0.5 Rated voltage (16V) Series name Type (mm) Voltage Size 5 6L 6.3 6L 8 7L 8 10L 8 12L 10 10L 10 12.7L 5.0 6.3 8.0 8.0 8.0 10.0 10.0 D V 2.5 4 6.3 10 16 20 25 5.9 6.0 6.9 9.9 11.9 9.9 12.6 L Code e g j A C D E A 6.0 7.3 9.0 9.0 9.0 11.0 11.0 5.3 6.6 8.3 8.3 8.3 10.3 10.3 B Frequency coefficient of rated ripple current 5.3 6.6 8.3 8.3 10.3 10.3 C 8.3 0 Frequency0/ 120Hz 1kHz 10kHz 100kHz or more E 1.6 2.1 3.2 3.2 3.2 4.6 4.6 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 Coefficient 0.05 0.30 0.70 1.00 H Dimension table in next page. CAT.8100K CL 12 0 C 01 2 D0.5 B0.2 E 0.5MAX. A0.2