1N5333B thru 1N5388B Zener Diode, 5 Watt 5% Tolerance Features: Zener Voltage: 3.3V to 200V High Surge Current Capability Absolute Maximum Ratings: DC Power Dissipation (T = +75C, Lead Length = 3/8), P ............................. 5W L D Derate Above 75 C ...................................................... 40mW/ C Forward Voltage (I = 1A), V ....................................................... 1.2V F F Operating Junction Temperature Range, T .................................. 65 to +200C J Storage Temperature Range, T .......................................... 65 to +200C stg Electrical Characteristics: (T = +25C unless otherwise specified) A Max Reverse Nominal Max Max Zener Impedance Leakage Current Zener Max Surge Voltage Max Voltage Test Current Regulation Regulator Z I Z I = 1mA V I Current ZT ZT ZK ZK i V Current Device Z ZT r Z (Note 1) (Note 1) I V (Note 1) (Note 3) Number I R R (Note 2) I ZT ZM Volts mA A Volts Amps Volt mA 1N5333B 3.3 380 3.0 400 300 1 20 0.85 1440 1N5334B 3.6 350 2.5 500 150 1 18.7 0.8 1320 1N5335B 3.9 320 2 500 50 1 17.6 0.54 1220 1N5336B 4.3 290 2 500 10 1 16.4 0.49 1100 1N5337B 4.7 260 2 450 5 1 15.3 0.44 1010 1N5338B 5.1 240 1.5 400 1 1 14.4 0.39 930 1N5339B 5.6 220 1 400 1 2 13.4 0.25 865 Note 1 Test conditions for zener voltage and impedance are as follows: I is applied 40 10ms prior Z to reading. Mounting contacts are located 3/8 to 1/2 from the inside edge of mounting clips to the body of the diode (T = +25C +8 , 2C). A Note 2 Surge current is specified as the maximum allowable peak, nonrecurrent squarewave cur- rent with a pulse width, PW, of 8.3ms. Mounting contact located as specified in Note 1. Note 3 Test conditions for voltage regulation are as follows: V measurements are made at 10% Z and then at 50% of the I max value listed in the Electrical Characteristic table. The test Z current time duration for each V measurement is 40 10ms (T = +25C +8, 2C). Mount- Z A ing contact located as specified in Note 1.Max Reverse Nominal Max Max Zener Impedance Leakage Current Zener Max Surge Voltage Max Voltage Regulation Test Current Regulator Z I Z I = 1mA Device V I Current ZT ZT ZK ZK i V Current Z ZT r Z (Note 1) (Note 1) I V (Note 1) (Note 3) Number I R R (Note 2) I ZT ZM Volts mA A Volts Amps Volt mA 1N5341B 6.2 200 1 200 1 3 12.4 0.1 765 1N5342B 6.8 175 1 200 10 5.2 11.5 0.15 700 1N5343B 7.5 175 1.5 200 10 5.7 10.7 0.15 630 1N5344B 8.2 150 1.5 200 10 6.2 10 0.2 580 1N5345B 8.7 150 2 200 10 6.6 9.5 0.2 545 1N5346B 9.1 150 2 150 7.5 6.9 9.2 0.22 520 1N5347B 10 125 2 125 5 7.6 8.6 0.22 475 1N5348B 11 125 2.5 125 5 8.4 8 0.25 430 1N5349B 12 100 2.5 125 2 9.1 7.5 0.25 395 1N5350B 13 100 2.5 100 1 9.9 7 0.25 365 1N5351B 14 100 2.5 75 1 10.6 6.7 0.25 340 1N5352B 15 75 2.5 75 1 11.5 6.3 0.25 315 1N5353B 16 75 2.5 75 1 12.2 6 0.3 295 1N5354B 17 70 2.5 75 0.5 12.9 5.8 0.35 280 1N5355B 18 65 2.5 75 0.5 13.7 5.5 0.4 265 1N5356B 19 65 3 75 0.5 14.4 5.3 0.4 250 1N5357B 20 65 3 75 0.5 15.2 5.1 0.4 237 1N5358B 22 50 3.5 75 0.5 16.7 4.7 0.45 216 1N5359B 24 50 3.5 100 0.5 18.2 4.4 0.55 198 1N5360B 25 50 4 110 0.5 19 4.3 0.55 190 1N5361B 27 50 5 120 0.5 20.6 4.1 0.6 176 1N5362B 28 50 6 130 0.5 21.2 3.9 0.6 170 1N5363B 30 40 8 140 0.5 22.8 3.7 0.6 158 1N5364B 33 40 10 150 0.5 25.1 3.5 0.6 144 1N5365B 36 30 11 160 0.5 27.4 3.3 0.65 132 1N5366B 39 30 14 170 0.5 29.7 3.1 0.65 122 1N5367B 43 30 20 190 0.5 32.7 2.8 0.7 110 1N5368B 47 25 25 210 0.5 35.8 2.7 0.8 100 1N5369B 51 25 27 230 0.5 38.8 2.5 0.9 93 1N5370B 56 20 35 280 0.5 42.6 2.3 1 86 1N5371B 60 20 40 350 0.5 42.5 2.2 1.2 79 Note 1 Test conditions for zener voltage and impedance are as follows: I is applied 40 10ms prior Z to reading. Mounting contacts are located 3/8 to 1/2 from the inside edge of mounting clips to the body of the diode (T = +25C +8 , 2C). A Note 2 Surge current is specified as the maximum allowable peak, nonrecurrent squarewave cur- rent with a pulse width, PW, of 8.3ms. Mounting contact located as specified in Note 1. Note 3 Test conditions for voltage regulation are as follows: V measurements are made at 10% Z and then at 50% of the I max value listed in the Electrical Characteristic table. The test Z current time duration for each V measurement is 40 10ms (T = +25C +8, 2C). Mount- Z A ing contact located as specified in Note 1.