EE-SPY415

Photomicrosensor (Reflective) EE-SPY415 Screw mounting, Reflective Photomicrosensor with a connector (Detectable sensing distance of 3 to 19 mm: white paper) Photo IC circuitry greatly improves response time Pulse modulation effectively reduces external light interference Convergent technology Be sure to read Safety Precautions on page 2. RoHS Compliant Model Number Structure EE-S P Y 4 15 (1) (2) (3) (4) (5) (4) (5) (1) (2) (3) Photo IC output, Light-ON 15: Serial number Photomicrosensor Light modulation Reflective Ordering Information Photomicrosensor Connecting Minimum packing Appearance Sensing method Sensing distance Output type Model method unit (Unit: pcs) Reflective Connector 118 mm Photo IC EE-SPY415 1 9.6 33 11 Note: Order in multiples of minimum packing unit. Specifications Absolute Maximum Ratings (Ta = 25C) Electrical and Optical Characteristics (Ta = 25C) Sym Rated Value Symbo Item Unit Remarks Item Unit Conditions bol value l MIN. TYP. MAX. Supply voltage VCC 7VDC --- Consumption ICC --- --- 25 mA With/without object Output transistor voltage current Output voltage VOUT 16 V (Between Collector and Emitter) Low level IOUT = 20 mA with VOL --- 0.4 0.4 V Output current IOUT 30 mA Output transistor collector current output voltage object Output power Output transistor collector High level VCC VOUT = VCC, RL = 1 K POUT 250 mW VOH --- --- V 1 dissipation * power dissipation output voltage by 0.9 Without object Operating -10 to Response tPLH Topr C --- --- --- 1 ms VOUT = VCC, RL = 1 K 2 temperature * 60 delay time * tPHL Storage -40 to Tstg C --- * Response delay time is defined as below. temperature 85 With object *1. Output power dissipation (POUT) must be derated in accordance with Figure 1 in the Engineering Data Section. Without object t *2. To be used in applications where no freezing or condensation occurs. V OH Output Voltage VOL Exterior Specifications t tPHL tPHL Material Connecting method Weight (g) Case ICC VCC Connecter 3.25 PPE I OUT RL V OUT VOH V OL GND 1EE-SPY415 Ratings Item Value Detectable distance * 11 2 mm (Black paper and OHP paper) 11 8 mm (White paper) Non-detectable distance * 20 mm (Black sponge) 45 mm (White paper) Usable ambient illumination 3,000 Lx max. at Receiver surface (incandescent lamp, fluorescent lamp) 10 to 150 Hz, Peak acceleration 10 G (100 m/s) 1.5 mm double amplitude for 2 hours Vibration Mechanical durability each in X, Y, Z directions 2 Shock Mechanical durability 300 m/s (approximately 30 G) in X, Y, Z directions, respectively 3 times Faulty operation 200 Vp, pulse width: 1 s Resistance to noise (normal mode) Break 350 Vp, pulse width: 1 s Faulty operation 250 Vp, pulse width: 1 s Resistance to noise (common mode) Break 500 Vp, pulse width: 1 s Tensile strength 2 kgf (20 N), for 5 seconds Terminal strength Flexure strength 1 kgf (10 N), 1 time, for 5 seconds * If a background object is present, the object should be located at the specified non-detectable distance or further from the receiver surface. White paper: reflection factor of 90% Black paper: reflection factor of 16% Engineering Data (Reference value) Fig 1. Output power dissipation vs. Ambient Temperature Characteristics 300 250 200 150 100 50 0 -40-30-20-10 010 20 30 40 50 60 70 80 90100 Ambient Temperature Ta (C) Safety Precautions To ensure safe operation, be sure to read and follow the Instruction Manual provided with the Sensor. CAUTION Precautions for Correct Use This product is not designed or rated for ensuring Do not use the product in atmospheres or safety of persons either directly or indirectly. Do not environments that exceed product ratings. use it for such purposes. Dispose of this product as industrial waste. Precautions for Safe Use Do not use the product with a voltage or current that exceeds the rated range. Applying a voltage or current that is higher than the rated range may result in explosion or fire. Do not miswire such as the polarity of the power supply voltage. Otherwise the product may be damaged or it may burn. Do not short-circuit the load. Otherwise explosion or burning may occur. This product does not resist water. Do not use the product in places where water or oil may be sprayed onto the product. 2 Output power dissipation POUT (mW)