Photomicrosensor (Transmissive) EE-SX4134 Dimensions Features Ultra-compact model. Note: All units are in millimeters unless otherwise indicated. Photo IC output model. Operates at a V of 2.2 to 7 V. CC PCB surface mounting type. RoHS Compliant. Absolute Maximum Ratings (Ta = 25C) Item Symbol Rated value Emitter Forward current I 25 mA (see note 1) F Reverse voltage V 5 V R Detector Supply voltage V 9 V CC Output voltage V 17 V OUT Output current I 8 mA OUT Optical axis Permissible output P 80 mW (see note 1) OUT Internal Circuit dissipation A V Ambient tem- Operating T 25 C to 85 C opr O perature Storage T 40 C to 90 C stg Unless otherwise specified, the K G tolerances are 0.15 mm. Reflow soldering T 255 C (see note 2) sol Terminal No. Name Manual soldering T 350 C (see note 2) sol A Anode K Cathode Note: 1. Refer to the temperature rating chart if the ambient temper- ature exceeds 25 C. V Supply voltage 2. Complete soldering within 10 seconds for reflow soldering (Vcc) and within 3 seconds for manual soldering. O Output (OUT) G Ground (GND) Ordering Information Description Model Photomicrosensor (transmissive) EE-SX4134 Electrical and Optical Characteristics (Ta = 25 C) Item Symbol Value Condition Emitter Forward voltage V 1.2 V typ., 1.4 V max. I = 20 mA F F Reverse current I 0.01 A typ., 10 A max. V = 5 V R R Peak emission wavelength 940 nm typ. I = 20 mA P F Detector Power supply voltage V 2.2 V min., 7 V max. --- CC Low-level output voltage V 0.12 V typ., 0.4 V max. V = 2.2 to 7 V, I = 8 mA, I = 7 mA OL CC OL F High-level output current I 10 A max. V = 2.2 to 7 V, I = 0 mA, V = 17 V OH CC F OUT Current consumption I 2.8 mA typ., 4 mA max. V = 7 V CC CC Peak spectral sensitivity 870 mm typ. V = 2.2 to 7 V P CC wavelength LED current when output is ON I 2.0 mA typ., 3.5 mA max. V = 2.2 to 7 V FT CC Hysteresis H 21% typ. V = 2.2 to 7 V (see note 1) CC Response frequency f 3 kHz min. V = 2.2 to 7 V, I = 5 mA, I = 8 mA (see note 2) CC F OL Response delay time t 7 s typ. V = 2.2 to 7 V, I = 5 mA, I = 8 mA (see note 3) PHL CC F OL Response delay time t 18 s typ. V = 2.2 to 7 V, I = 5 mA, I = 8 mA (see note 3) PLH CC F OL Photomicrosensor (Transmissive) EE-SX4134 2013. The following illustrations show the definition of response Note: 1. Hysteresis denotes the difference in forward LED delay time. current value, expressed in percentage, calculated from the respective forward LED currents when the photo IC in turned from ON to OFF and when the Input photo IC in turned from OFF to ON. 2. The value of the response frequency is measured by rotating the disk as shown below. Output Disk 2.1 mm 0.5 mm 0.5 mm Engineering Data Forward Current vs. Collector Forward Current vs. Forward LED Current vs. Supply Voltage Dissipation Temperature Rating Voltage Characteristics (Typical) (Typical) Ta = 25C R = 4.7 k L Ta = 30C Ta = 25C Ta = 70C Supply voltage V (V) CC Forward voltage V (V) Ambient temperature Ta (C) F Low-level Output Voltage vs. Am- LED Current vs. Ambient Temper- Low-level Output Voltage vs. bient Temperature Characteristics ature Characteristics (Typical) Output Current (Typical) (Typical) V = 5 V Ta = 25C CC R = 4.7 k L V = 5 V V = 5 V CC CC I = 8 mA I = 7 mA OL F I = 7 mA F I = 8 mA OL I = 0.5 mA OL Output current I (mA) C Ambient temperature Ta (C) Ambient temperature Ta (C) Current Consumption vs. Supply Response Delay Time vs. Forward Repeat Sensing Position Voltage (Typical) Current (Typical) Characteristics (Typical) 40 IF ICC Ta = 25C VCC RL 35 VCC = 5 V Ta = 25C Ta = 25C OUT I = 0 mA I = 5 mA F VOUT R = 4.7 k F L V = 5 V GND CC 30 R = 4.7 k L n = repeat 20 times 25 20 tPLH 15 INPUT IF 0.01 t 10 OUTPUT t tPHL tPLH 5 tPHL 0 03510 15 20 250 Distance d (mm) Supply voltage V (V) CC Forward current I (mA) F Unit: mm (inch) 202 Photomicrosensor (Transmissive) EE-SX4134 Current consumption Icc (mA) LED current I (mA) Forward current I (mA) FT F Output allowable dissipation P (mW) C Low level output voltage V (V) Forward current I (mA) OL F Response delay time t , t (s) PHL PLH Output transistor Low level output voltage V (V) OL LED current I (mA) FT