Ordering number : ENA2159A LV5696P Bi-CMOS IC LV5696P Specifications Absolute Maximum Ratings at Ta = 25C Parameter Symbol Conditions Ratings Unit Maximum supply voltage V max 36 V CC Power dissipation Pd max IC Unit 1.5 W 3 At using Al heat sink of (50 501.5mm) 5.6W Infinite large heat sink 32.5 W Peak voltage V peak See below about Pulse wave 50 V CC Operating temperature Topr -40 to +85 C Storage temperature Tstg -55 to +150 C Junction maximum temperature Tj max 150 C Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. Recommended Operating Conditions at Ta = 25C Parameter Conditions Ratings Unit Power supply voltage rating 1 V output, ANT output 7.5 to 16 V DD Power supply voltage rating 2 AUDIO output 10.5 to 16 V Power supply voltage rating 3 CD output, ILM output, SYS output, DSP output 10 to 16 V *Make sure that V 1 is as follows: V 1 > V - 0.7V CC CC CC Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond the Recommended Operating Ranges limits may affect device reliability. Electrical Characteristics at Ta = 25C, V = V 1 = 14.4V CC CC Ratings Parameter Symbol Conditions Unit min typ max Quiescent current I V No Load, CTRL1/2/3 = L/L/L 50 100 A CC DD CTRL1 (ANT) Low input voltage V1 ANT: OFF 0 0.3 V IL High input voltage V1 ANT: ON 2.7 3.3 5.5 V IH Input impedance R1 input voltage 3.3V 280 400 520 k IN CTRL2 (ILM) Low input voltage V2 ILM: OFF 0 0.3 V IL High input voltage V2 ILM: ON 2.7 3.3 5.5 V IH Input impedance R2 input voltage 3.3V 280 400 520 k IN CTRL3 Low input voltage V 3 CD, AUDIO, SYS5V, DSP: OFF 0 0.3 V IL Middle input voltage V 3 CD, DSP:OFF 1.3 1.65 2.0 V IM SYS5V, AUDIO: ON High input voltage V 3 CD, AUDIO, SYS5V, DSP: ON 2.7 3.3 5.5 V IH Input impedance R3 input voltage 3.3V 280 400 520 k IN V output 5.0V/3.3V -ON IKV = V 1 : V = 5V/IKV = GND : V = 3.3V DD DD CC DD DD DD V output voltage 1 V1 I 1 = 200mA, IKV = V1 4.755.0 5.25V DD O O DD CC V output voltage 2 V 1 I 1 = 200mA, IKV = GND 3.13 3.3 3.47 V DD O O DD V output current I1 200 mA DD O Line regulation V 1 7.5V < V < 16V, I 1 = 200mA 30 100 mV OLN CC O Load regulation V 1 1mA < I 1 < 200mA 70 150 mV OLD O Dropout voltage 1 V 1 I 1 = 200mA 1.0 1.5 V DROP O Dropout voltage 2 V 1 I 1 = 100mA 0.5 0.75 V DROP O Ripple rejection R 1 f = 120Hz, I 1 = 200mA 40 50 dB REJ O Continued on next page. No.A2159-2/15