Ordering number : ENA1032A STK621-061-E Thick-Film Hybrid IC 3-Phase Motor Drive STK621-061-E Specifications Absolute Maximum Ratings at Tc = 25C Parameter Symbol Conditions Ratings unit Supply voltage V + - , surge < 500V *1 450 V CC Collector-emitter voltage V + - U (V, W) or U (V, W) - 600V CE Output current I +, , U, V, W terminal current 30 A O Output peak current Iop +, , U, V, W terminal current PW = 100s 45 A Pre-driver supply voltage VD1, 2, 3, 4 VB1 - U, VB2 - V, VB3 - W, V - V *2 20 V DD SS Input signal voltage V HIN1, 2, 3, LIN1, 2, 3 terminal 0 to 7 V IN FAULT terminal voltage VFAULT FAULT terminal 20 V Maximum loss Pd Per 1 channel 49 W Junction temperature Tj IGBT, FRD junction temperature 150 C Storage temperature Tstg -40 to +125 C Operating temperature TC H-IC case temperature -20 to +100 C Tightening torque A screw part at use M4 type screw *3 1.17 Nm Withstand voltage Vis 50Hz sine wave AC 1 minute *4 2000 VRMS In the case without the instruction, the voltage standard is - terminal = V terminal voltage. SS *1 Surge voltage developed by the switching operation due to the wiring inductance between the + and terminals. *2 VD1 = between VB1-U, VD2 = VB2-V, VD3 = VB3-W, VB4 = V -V , terminal voltage. DD SS *3 Flatness of the heat-sink should be lower than 0.25mm. *4 The test condition is AC 2500V, 1 second. Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. Electrical Characteristics at Tc=25C, VD=15V Test Ratings Parameter Symbol Conditions unit Circuit min typ max Power output part Collector-to-emitter cut-off current I V = 600V Fig.1 0.5 mA CE CE Boot-strap diode reverse current IR (BD) VR (BD) = 600V Fig.1 0.5 mA Collector-to-emitter saturation voltage V (SAT) I = 15A Upper side 1.8 V CE O Fig.2 Lower side 2.0 V Diode forward voltage V I = -15A Upper side 1.7 V F O Fig.3 Lower side 1.9 V Junction-to-substrate thermal resistance j-c (T) IGBT 2.1 C/W j-c (D) FWD 2.5 C/W Control (Pre-driver) part Pre-drive power supply consumption I VD1, 2, 3 = 15V 0.07 0.4 D Fig.4 mA electric current VD4 = 15V 2 5 Input ON voltage V Output ON 0.8 V IH Input OFF voltage V Output OFF 3.0 V IL Protection part Excessive temperature TSD The substrate surface 100 120 C Overcurrent protection electric current ISD PW = 100s Fig.5 46 58A Pre-drive low voltage protection UVLO 10 12 V Fault terminal input electric current IOSD VFault = 0.1V 0.5 mA Fault clearness delay time FLTCLR After each protection 18 80ms operation ending Board Temperature Mounting resistance Rt Resistance between the Fault 90 110k and V terminals SS Switching time tON I = 15A, Inductive load 0.8 s O Fig.6 tOFF 1.0 s Electric current output signal level ISO I = 15A 0.141 V O In the case without the instruction, the voltage standard is - terminal = V terminal voltage. SS No.A1032-2/8