ESD Suppressor EZAEG type EZAEG 1N, 2N series Don t use these products in the engine room. Don t use these products in any driving applications or any other critial functions that may affect passanger s sagety. (e.g. Power train, ABS, Engine ECU, Air bag, and so on.) Dont use these products in applications related to the autonomous driving equipment with system level 3 or higher. Features Good ESD withstanding (IEC61000-4-215 kV contact/air Discharge) ESD protection of high-speed data lines Low capacitance 0603 (0201) size : 0.04 pF, 1005(0402) size : 0.05 pF Good ESD suppression characteristics RoHS compliant Recommended applications Smart phones, Mobile phones, RF Modules, NFC and GPS ESD suppresion of high-speed differential data line such as Antena circuit, HDMI, SATA, USB, Display Port Explanation of part numbers 1 2 3 4 5 6 7 8 9 10 11 E Z A E G 2 N 5 0 A X Product code Size Design specification Peak voltage Special Feature Packing methods Size mm (inch) Code Design specification Code Voltage Code Feature Code Packaging Part No. ESD Code Suppressor 1 0603 (0201) 50 500 V A Standard Pressed carrier taping ESD withstanding EZAEG1N C 2 mm pitch, 15,000 pcs 2 1005 (0402) 15 kV, N Rated voltage Pressed carrier taping EZAEG2N X 30 V 2 mm pitch, 10,000 pcs Construction Circuit configuration Gap electrode Protective coating Alumina substrate Electrode (Between) ESD absorbent material Electrode (Outer) Dimensions (not to scale) L a W T b Unit : mm Mass Part No. Dimensions (Weight) (inch size) L W b T (g/1000 pcs) a EZAEG1N 0.600.03 0.300.03 0.150.10 0.150.10 0.230.03 0.12 (0201) EZAEG2N 1.000.10 0.500.05 0.200.10 0.270.10 0.380.05 0.60 (0402) Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 14-May-21ESD Suppressor Ratings *1 Part number Capacitance Rated voltage Category temperature range EZAEG1N50AC 0.04+0.04/-0.03 pF 30 V max. 55 to +125 EZAEG2N50AX 0.05+0.05/-0.04 pF *1: Capacitance = The capacitance value shall be measured under the conditions specified below. Frequency1 MHz 10 %Voltage1 Vrms 0.2 VrmsTemperature25 2 Perfomance Performance Test item Test conditions requirements Peak voltage 500 V max. IEC61000-4-2, contact discharge 8 kV, Peak voltage value Clamping voltage 100 V max. IEC61000-4-2, contact discharge 8 kV, voltage at 30 ns after initiation of pulse Leakage current 1 A max. Current at rated voltage (DC 30 V) ESD withstanding IEC61000-4-2, contact discharge 15 kV or air discharge 15 kV, +/ 50 times Rapid change of temperature 55 (30 min.) /+125 (30 min.), 100 cycles Leakage current Load life in humidity 60 , 90 % to 95 %RH, Rated voltage, 1000 h 10 A max. Endurance at 85 85 , Rated voltage, 1000 h Resistance to soldering heat 270 , 10 s Frequency characteristics ESD Suppression voltage waveform 400 5 350 0 300 -5 250 -10 200 150 -15 100 -20 50 -25 0 -30 -50 1 10 100 1000 10000 200 -20 0 20 40 60 80 100 120 140 160 180 Frequency (MHz) Times (nSecs) Typical circuits requiring protection HDMI circuit Antenna circuit Antenna HDMI Controller Ga/As-SW HDMI or Rx/Tx ASM Recommended land pattern Recommended land pattern design for ESD Suppressor is shown below. ESD Suppressor Unit : mm Dimensions Part number a b c EZAEG1N 0.3 to 0.4 0.8 to 0.9 0.25 to 0.35 a EZAEG2N 0.5 to 0.6 1.4 to 1.6 0.40 to 0.60 b As for packaging methods, soldering conditions and safety precautions, please see data files. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 14-May-21 Attenuation (dB) c Volts (V)