SAFETY DATA SHEET according to 1907/2006/EC, Article 31 Page 1 of 4 Permabond 102 (C2) Revision 6 Revision date 02-08-2011 1. IDENTIFICATION OF THE SUBSTANCE / PREPARATION AND THE COMPANY Product name Permabond 102 (C2) Company Permabond Engineering Adhesives Ltd Wessex Business Park Wessex Way Colden Common Hampshire SO21 1WP United Kingdom Telephone +44 (0)1962 711661 Fax +44 (0)1962 711662 Intended use Adhesives. 2. HAZARDS IDENTIFICATION Main hazards Irritating to eyes, respiratory system and skin. Skin contact On contact, immediate bonding of the skin will occur. Eye contact On contact, will bond eyelids together. Vapours are lachrymatory. Ingestion On contact, immediate bonding of mouth could occur. Personal precautions No precautions required to be mentioned. Environmental precautions No environmental requirements. 3. COMPOSITION / INFORMATION ON INGREDIENTS Hazardous ingredients Conc. CAS EINECS Symbols/Risk phrases Ethyl-2-cyanoacrylate 50-100% 7085-85-0 230-391-5 Xi R36/37/38 (Ethyl cyanoacrylate) 4. FIRST AID MEASURES Skin contact No attempt should be made to remove material from skin or to remove contaminated clothing, as the bonded skin can be easily torn. If symptoms develop, obtain medical attention. Eye contact Rinse immediately with plenty of water for 15 minutes holding the eyelids open. Seek medical attention. Cured adhesive will not bond well to surface of eye, but corneal damage from abrasion may result. Inhalation Move the exposed person to fresh air. Get medical attention if irritation persists. Ingestion Immediate medical attention is required. Treat symptomatically and supportively. Copyright 2011 ChemSoft Limited. All rights reserved. Print date 02-08-2011Page 2 of 4 Permabond 102 (C2) Revision 6 Revision date 02-08-2011 5. FIRE FIGHTING MEASURES Extinguishing media Carbon dioxide (CO2) , dry chemical. Fire hazards Cloths used to wipe up spills may cause rapid polymerization that could generate sufficient heat to ignite the cloth. Decomposes upon heating to release toxic fumes of nitrogen oxides, carbon monoxide, carbon dioxide, and hydrogen cyanide. Protective equipment Wear: Self-contained breathing apparatus. 6. ACCIDENTAL RELEASE MEASURES Personal precautions Ensure adequate ventilation of the working area. Wear suitable protective equipment. Environmental precautions No environmental requirements. Clean up methods Small spills: wipe up with cloth. Immediately soak cloth with water to polymerize the adhesive. Caution Cloth containing adhesive may undergo autoignition if not soaked with water. Large spills: flood area with water. When cured, remove film with a scraper. Wear approved respirator for organic vapours if needed, and protective clothing. 7. HANDLING AND STORAGE Handling Always replace cap after use. Storage Keep in a cool, dry, well ventilated area. Keep containers tightly closed. 8. EXPOSURE CONTROLS / PERSONAL PROTECTION Exposure limits Ethyl-2-cyanoacrylate WEL 8-hr limit ppm: - WEL 8-hr limit mg/m3: - (Ethyl cyanoacrylate) WEL 15 min limit ppm: 0.3 WEL 15 min limit mg/m3: 1.5 Engineering measures Normal (mechanical) room ventilation should be adequate for small volumes. For higher volume activities, or if needed for worker comfort, local mechanical exhaust should be provided. Respiratory protection Not normally required. Hand protection Nitrile rubber or Viton gloves are recommended. Cotton or other absorbent gloves should not be worn. Gloves should conform to EN 374. Eye protection Safety glasses, goggles or face shield to protect against splashing. Personal eye protection should conform to EN 166 Protective equipment Uniforms, coveralls, or a lab coat should be worn. Wash hands before eating, drinking, or using toilet facilities. 9. PHYSICAL AND CHEMICAL PROPERTIES Description Liquid. Colour Colourless. Odour Pungent. Boiling point >100C Flash point 83C Vapour pressure <0.5 mm Hg Relative density 1.05 Water solubility Insoluble in water. Viscosity ~100 mPa.s Vapour density >1 Copyright 2011 ChemSoft Limited. All rights reserved. Print date 02-08-2011