Radiant Heater and Fan Heater series FLH Heat generated by electrical equipment operating under load will prevent the accumulation of condensation. After the equip- ment has been switched off however it cools down and gra- dually adapts to the ambient temperature, thus dropping below the dew point. This is the signal that triggers the radiant heater These sources of heat prevent the formation of condensation by raising the internal temperature a few degrees above the ambient temperature. In the interest of evenly distributing the heat, we recommend that the requirement of heating capacity is divided among several small heaters. 230 V IP 44 115 V Level of suitable for both 115 V 230 V protection 50 Hz and 60 Hz (FLH 010-150) Thermal data: Radiant Heater Fan Heater FLH 010 FLH 015 FLH 030 FLH 045 FLH 060 FLH 075 FLH100 FLH 150 FLH 250 FLH 400 Heater power (T = + 20 C) 10 Watt 15 Watt 30 Watt 45 Watt 60 Watt 75 Watt 100 Watt 150 Watt 250 Watt 400 Watt u Max. surface temperature approx. 55 C 65 C 90 C 105 C 105 C 120 C 130 C 150 C 70 C 85 C 3 3 Airflow 50 m /h (50 Hz) 61 m /h (60 Hz) Duty cycle 100 % Heating element PTC (positive temperature coefficient), temperature refulating resistance type with temperature monitor Electrical data: 1 Rated voltage ) 230 V (50 / 60 Hz) 115 V or 230 V Rated frequency 110 - 250 V 104 - 126 V or 207 - 258 V Power consumption 10 Watt 15 Watt 30 Watt 45 Watt 60 Watt 75 Watt 100 Watt 150 Watt 260 Watt 410 Watt Starting current approx. 1,0A 1,1A 1,2A 1,8A 2,5A 4,5A 5,0A 7,5A 2,2A / 1,1A 3,6A / 1,8A 1 ) other voltages (24 V DC, 48V DC) on request Mechanical data: Fitting position any, vertical position preferred airflow vertical, exit at top Construction aluminium section, anodised (light-coloured) Weight 250 g 250 g 250 g 250 g 450 g 510 g 510 g 770 g 1.035 g 1.200 g Dimensions AAAA B B B C D E Protection class I I Connection cable end or plug-in terminal plug-in terminal 2 2 Binding post clambing area single filament: 2 x 0,5 - 2,5 mm , fine multi-filament: (soldered, wire and sleeve, pin terminal) 2 x 0,5 - 1,5 mm Mounting method snap-in mounting for 35mm profile bar in accordance with EN 50022 Supplementary data: Operating temperature - 40 C (- 40 F) ... + 70 C (+ 158 F) - 20 C (- 4 F) ... + 70 C (+ 158 F) Storage temperature - 40 C (- 40 F) ... + 70 C (+ 158 F) - 40 C (- 40 F) ... + 70 C (+ 158 F) System of protection IP 44 (cable end), IP 20 (plug-in terminal), when installed as specified IP 20, when installed as specified Accessories thermostat FLZ 510, FLZ 520, FLZ 530, hygrostat FLZ 600 Approvals UL approval Optional extra 2nd protection guard 114 We reserve the right to technical alterations.Subject to correction. 075000031ELECTRO-TECHNOLOGY FOR INDUSTRY Mechanical data FLH 010 - FLH 150 plug-in terminal cable end FLH 250 / FLH 400 104 85 85 104 with guard without guard 115 90 65 D=186,5 / E=226,5 90 65 D=183,5 / E=223,5 We reserve the right to technical alterations.Subject to correction. 075000031