J1V-U2100NL

Declaration of Conformity to EU RoHS Directive EU 2015/863 Pulse Electronics manufactures products at Pulse Operations or with selected Manufacturing Partners Pulse Electronics 15255 Innovation Drive 100 San Diego, CA 92128 Tel: 858-674-8100 Part number: J1V-U2100NL This is to certify that the parts/products listed above meet the requirements of the RoHS Directive (EU) 2015/863 The following table lists the restricted materials and their respective allowable limits: RoHS Restricted Substance Allowable Limit Cadmium and its compounds* 100 ppm (0.01 weight %) Mercury and its compounds 1000 ppm (0.1 weight %) Hexavalent chromium and its compounds 1000 ppm (0.1 weight %) Lead and its compounds ** 1000 ppm (0.1 weight %) Polybrominated biphenyls (PBB) 1000 ppm (0.1 weight %) Polybrominated diphenyl ethers (PBDE) 1000 ppm (0.1 weight %) Phthalate (2 - ethyl hexyl ester (DEHP) 1000 ppm (0.1 weight %) Butyl Benzyl Phthalate (BBP) 1000 ppm (0.1 weight %) dibutyl phthalate (DBP) 1000 ppm (0.1 weight %) Di Iso Butyl Ortho Phthalate (DIBP) 1000 ppm (0.1 weight %) If parts/products take advantage of any exceptions, please check which exemption(s): 1. Mercury in single capped (compact) fluorescent lamps not exceeding (per burner): (a) For general lighting purposes < 30 Watts (b) For general lighting purposes 30 Watts and < 50 Watts (c) For general lighting purposes 50 Watts and < 150 Watts (d) For general lighting purposes 150 Watts: 15 mg (e) For general lighting purposes with circular or square structural shape and tube diameter 17 mm (f) For special purposes: 5 mg (g) For general lighting purposes < 30Wwith a lifetime equal or above 20000h: 3,5mg 2a. Mercury in double-capped linear fluorescent lamps for general lighting purposes not exceeding (per lamp): (1) Tri-band phosphor with normal lifetime and a tube diameter < 9 mm (e.g. T2) (2) Tri-band phosphor with normal lifetime and a tube diameter 9 mm and 17 mm (e.g. T5) (3) Tri-band phosphor with normal lifetime and a tube diameter > 17 mm and 28 mm (e.g. T8) (4) Tri-band phosphor with normal lifetime and a tube diameter > 28 mm (e.g. T12) (5) Tri-band phosphor with long lifetime ( 25,000h) 2b. Mercury in other fluorescent lamps not exceeding (per lamp): (1) Linear halophosphate lamps with tube diameter > 28mm (e.g. T10 and T12): 10 mg (2) Non-linear halophoshate lamps (all diameters): 15mg (3) Non-linear tri-band phosphor lamps with tube diameter > 17 mm (e.g. T9) (4) Lamps for other general lighting and special purposes (e.g. induction lamps) 3. Mercury in cold cathode fluorescent lamps and external electrode fluorescent lamps (CCFL and EEFL) for special purposes not exceeding (per lamp): (a) Short length (500 mm) (b) Medium length (> 500 mm and 1500 mm) (c) Long length (> 1500 mm) 4a. Mercury in other low pressure discharge lamps (per lamp) 4b. Mercury in High Pressure Sodium (vapor) lamps for general lighting purposes not exceeding (per burner) in lamps with improved color rendering index Ra > 60: (I) P 155 W (II) 155 < P 405 W (III) P > 405 W 4c. Mercury in other High Pressure Sodium (vapor) lamps for general lighting purposes not exceeding (per burner): (I) P 155 W (II) 155 < P 405 W (III) P > 405 W 4d. Mercury in High Pressure Mercury (vapor) lamps (HMPV) 4e. Mercury in metal halide lamps (MH) 4f. Mercury in other discharge lamps for special purposes not specifically mentioned in Annex 4g. Mercury in hand crafted luminous discharge tubes used for signs, decorative or architectural and specialist lighting and light-artwork, where the mercury content shall be limited as follows: (a). 20mg per electrode pair + 0,3mg per tube length in cm, but not more than 80mg, for outdoor applications and indoor applications exposed to temperatures below 20C (b). 15mg per electrode pair + 0,24mg per tube length in cm, but not more than 80mg, for all other indoor applications. 5a. Lead in glass of cathode ray tubes 5b. Lead in glass of fluorescent tubes not exceeding 0.2% by weight 6a. Lead as an alloying element in steel for machining purposes and in galvanized steel containing up to 0.35% lead by weight 6b. Lead as an alloying element in aluminium containing up to 0.4% lead by weight 6c. Copper alloy containing up to 4% lead by weight 7a. Lead in high melting temperature type solders (i.e. lead-based alloys containing 85% by weight or more lead) 7b. Lead in solders for servers, storage and storage array systems, network infrastructure equipment for switching, signaling, transmission, and network management for telecommunications 7c-I. Electrical and electronic components containing lead in a glass or ceramic other than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or ceramic matrix compound 7c-II. Lead in dielectric ceramic in capacitors for a rated voltage of 125 V AC or 250 V DC or higher