THT Power Inductors Toroid - Vertical, Low Profile and Klipmount Available in vertical, low profile and Klipmount SMPS averaging filter Characterized for general purpose use and ripple filters Single-layer designs 3 Can be used as differential mode inductors in EMI filters Electrical Specifications 25C - O perating Temperature -40 C to 130C Reference Operating Values Design Control Values 1 Vertical Low Profile Inductance ET Inductance 20 kHz Coil Klip* Lead 4 op IDC DCR Part Part Typical (V-Sec) No DC (H) Test mV Size Mount Diameter (AMPS) ( MAX) Number Number (H) ( 20%) No DC Code Package (in .003) PE-51591NL - 20 2.0 52 32.8 33 .060 H - .020 PE-92100NL - 25 2.6 30 20.7 22 .043 A KM1 .020 PE-92101NL PE-92401NL 50 2.6 50 45.7 45 .071 B KM2 .020 PE-92102NL PE-92402NL 100 2.6 90 94.1 90 .100 C KM3 .020 PE-92103NL - 35 2.6 55 28.4 36 .037 B KM2 .025 PE-92104NL PE-92404NL 70 3.0 85 61.0 73 .052 C KM3 .025 PE-92105NL PE-92405NL 145 3.0 140 141.8 140 .087 D KM4 .025 PE-92106NL - 285 3.0 300 264.1 340 .140 E KM5 .025 PE-92107NL - 450 3.0 425 436.3 500 .200 F - .025 PE-92108NL PE-92408NL 59.6 3.6 130 90.7 120 .045 D KM4 .032 PE-92109NL - 165 4.0 240 152.0 260 .070 E KM5 .032 PE-92110NL - 270 4.0 350 263.9 400 .100 F - .032 PE-92111NL - 40 4.0 70 37.9 57 .027 C KM3 .032 PE-51590NL - 22 5.0 44 20.3 37 .020 G - .032 PE-92112NL PE-92412NL 100 5.0 200 90.7 180 .034 E KM5 .042 PE-92113NL - 170 5.0 300 159.7 310 .050 F - .042 PE-92114NL PE-92414NL 35.6 5.0 100 55.6 88 .023 D KM4 .042 PE-92115NL - 95 7.0 225 96.0 200 .025 F - .051 PE-92116NL PE-92416NL 55 7.0 150 49.1 100 .017 E KM5 .051 PE-92117NL - 55 10.0 175 55.9 120 .013 F - .064 * Parts available with KlipMount option can be ordered by adding a K suffix to the part number (i.e. PE-92100K). 1 power.pulseelectronics.com P635. C (07/18) THT Power Inductors Toroid - Vertical, Low Profile and Klipmount Relationships Between Reference and Operating Conditions Mechanical Schematic Klipmount Package Base material meets flammability requirements of UL 94V-0 Mechanically rigid mount PC Board - automatic insertability Lowest cost A B C D H EV) Standard Package Maximum Typical .340 .580 .650 .29 .110 KM-1 8,64 14,73 16,51 7,37 2,79 .450 .650 .700 .325 .150 KM-2 11,43 16,51 17,78 8,26 3,81 .450 .850 .950 .415 .150 KM-3 11,43 21,59 24,13 10,54 3,81 .620 .970 1.10 .475 .225 KM-4 15,50 24,64 27,94 12,07 5,72 .700 1.30 1.40 .625 .250 KM-5 17,78 33,02 35,56 15,88 6,35 Note: Units with large wire sizes may exceed B dimension. KLIPMOUNT is a trademark of Pulse Engineering, Inc. Inches .010 Dimensions: Unless otherwise specified, all tolerances are mm 0,25 2 power.pulseelectronics.com P635. C (07/18)