Universal AC Input Features Constant Current Operation LIGHTLINE Suitable for High Brightness LED Products LED DRIVER AC/DC-Converter Built-In Active PFC Function Overvoltage-, Short Circuit- and Over- with 5 year Warranty temperature Protection Built-In 3 in 1 Dimming IP67 Rated Class 2 Power Unit UL1310 Selection Guide Part Output Rated Rated Output Efficiency 60 Watt PFC Number Voltage Power Current Voltage Range (VDC) (W) (mA) (V) (typ.) RACD60-1050A 57 60 105 - 1050 40 - 57 88% Single 230 500 21-39 Triac 82 RACD60-1200A 48 58 120 - 1200 33 - 48 88% Output RACD60-1650A 36 60 165 - 1650 24 - 36 87% 12-18 RACD60-2500A 24 60 250 - 2500 15 - 24 86% RACD60-4200A 12 50 420 - 4200 9 - 12 86% Specifications (measured at 230VAC and 25C ambient temperature) Input Voltage Range 90-305 VAC Input Frequency Range 47-63Hz Power Factor (Full Load) 120VAC >0.98 240VAC >0.94 RoHS 2011/65/EU 277VAC >0.92 6/6 E340696 THD Full Load, 115VAC 12% max. Full Load, 230VAC 18% max. EN 61347-1 Certified DC Dimming DC 1-10V EN 61347-2-13 Certified PWM Dimming Puls: Hi=10V Low=0V, Duty: 10% - 100%, Fsw 0.5 - 3KHz UL8750 Certified Resistance Dimming 10K - 100K Current Accuracy 5% AC Input Current 100-240VAC 0.8A 277VAC 0.4A RACD60-A Inrush Current (Cold Start) 240VAC 70A Leakage Current <0.5mA / 240VAC Start-up Time (at Full Load) <2sec Isolation Voltage 3.75kVAC / 1 minute Derating-Graph Short Circuit Protection Hiccup Over Voltage Protection 12V 13.2 - 15.6V (Ambient Temperature) 24V 26.4 - 31.2V 36V 39.6 - 46.8V A 48V 52.8 - 62.4V 3 A 57V 62.7 - 70V /+A Over Temperature Protection 105 10C, Latch Mode - A Vibration 10-500Hz, 2G, 60 Min. along X, Y and Z Storage Humidity 10% - 90% RH , A Operating Humidity 20% - 90% RH Non-Condensing A Weight 420g Operating Temperature -30C to +50C 0* + -+ Storage Temperature -40C to +60C ) Ripple & Noise 12V, 24V 200mV Note: (at 20MHz bandwidth using 0.1uF & 47uF capacitor) 36V, 48V, 57V 250mV All LED Drivers may not be used without a load. IP Rating IP67 Isolation Resistance 100M / 500VDC at 25C They must be switched on the primary side only. Dimension (L*W*H) 179*45.1*32.5mm Noncompliance may damage the LED or reduce Design Lifetime 70 x 10 hours max. its lifetime. MTBF (+25C) using MIL-HDBK 217F 200 x 10 hours min. Refer to Application Notes continued on next page L-54 REV: 0/2015 www.recom-power.com NOT RECOMMENDED FOR NEW DESIGNS * 2) RACD60-A ) 89 RACD60-A LIGHTLINE AC/DC-Converter Series Specifications (measured at 230VAC and 25C ambient temperature) Safety Standards LED Lighting Safety Report: E340696 UL8750 LED Lighting Safety (Canada) Report: E340696 cUL8750 Class 2 Power Supply Safety Report: E340696 UL1310 Extra Low-Voltage Class 2 Output Report: E340696 CSA C22.2 No. 223-M91 LED equipment for lighting application Report: E340696 CSA C22.2 No. 250.13-12 EN61347-1 EN61347-2-13 EN61000-3-2 Class C EN61000-3-3 EN61000-4-2,3,4,5,6,8,11 EN61547 EN55015 FCC15 3 in 1 Dimming Control (DC / PWM / Resistance) 10K-100K Resistor Dimmable (Typical): Resistor Single-Driver 10K 20K 30K 40K 50K 60K 70K 80K 90K 100K Multi-Driver 10K/N 20K/N 30K/N 40K/N 50K/N 60K/N 70K/N 80K/N 90K/N 100K/N Iout (%) 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% The length of extended wire for DIM+/- shall not exeed 20 meters. (wire 20m) N = The number of dimmer drivers should not exceed 15. (N 15mS) DC: 1-10V Dimmable (Typical) DC: 10V / PWM Dimmable (Typical) % % ) * * ( Typical Characteristics Efficiency vs Load over Vin Maximum Number of LED drivers per circuit breakers RACD60-2500A Condition Circuit Breaker Circuit Breaker Current Typ 10A 16A 20A 25A 115VAC, 1Ohm % C 12 20 24 31 90 phase angle % B 13 21 25 32 230VAC, 1Ohm 90 phase angle C 21 35 41 51 % B 15 24 29 37 277VAC, 1Ohm 90 phase angle C 24 40 47 58 % % Package Style & Pinning -, : & ( . ) ) 9 4 - 21 7 ) 4 5 *. 20 4 (> * : & ,+% 1 4 ( * %+ / C + 0 *+%/ ( . - C + %. - *%+ 9 G 0 20 ( ( , . - * . %. 4 %. / C + - C + * The product information and specifications are subject to change without prior notice. RECOM products are not authorized for use in safety-critical applications (such as life support) without RECOMs explicit written consent. A safety-critical application is defined as an application where a failure of a RECOM product may reasonably be expected to endanger or cause loss of life, inflict bodily harm or damage property. The buyer shall indemnify and hold harmless RECOM, its affiliated companies and its representatives against any damage claims in connection with the unauthorized use of RECOM products in such safety-critical applications. www.recom-power.com REV: 0/2015 L-55 ( +,, * ( 1 8 (