RACT12-300 Recom Power

C C S S O O R R w E E M M T T P P R R a L L R I I E E A A r V V N N A N N T T r Triac dimmable with leading or trailing edge dimmers Features Class II with SELV output (no earth required) AC/DC Converter TRIAC Dimmable Extra-large screw terminals and integrated cable clamps for easy installation LED Power factor corrected >0.95 Dimming range 1..100% Driver RACT12 Compatible with a wide range of dimmers Description 12 Watt The RACT12-xxx series are low cost, triac-dimmable, constant current 12W LED drivers available 3 with either 300mA, 350mA, 500mA or 700mA full-range outputs. The drivers are Class II (double TRIAC insulated) meaning no earth connection is required. The phase angle dimming works with leading or trailing edge dimmers. The RACT12 is suitable for indoor locations up to 50C ambient temperature and is Dimmable certified for building into furniture for applications such as dimmable shelf lighting, cove lighting or accent lighting. It is CE marked (LVD + EMC + RoHS), EAC and has IEC61347-1/IEC61347-2-13 CB report Single Output certification. Selection Guide Part Input Output Output Efficiency Output Number Voltage Range Voltage Range Current min. rated load Power VAC VDC mA % W RACT12-300 198-264 20-40 300 82 12 RACT12-350 198-264 18-35 350 81 12 RACT12-500 198-264 12-24 500 81 12 22++ RACT12-700 198-264 9-18 700 81 12 RoHSRoHS REACHREACH compliantcompliant compliantcompliant 10 from 1010 from 10 All LED Drivers may not be used without a load. They must be switched on the primary side only. Noncompliance may damage the LED or reduce its lifetime. M M Model Numbering RACT12- Output Power Output Current IEC/EN61347 certified IEC/EN61347-2-13 certified EN61547 certified EN62493 certifed Specifications (measured Ta= 25C, 240VAC, rated load unless otherwise specified) EN55015 compliant CB report BASIC CHARACTERISTICS Parameter Condition Min. Typ. Max. Input Voltage Range 198VAC 230VAC 264VAC Input Current 80mA Inrush Current full load 5A No Load Power Consumption 1W Input Frequency Range 50Hz 60Hz Power Factor full load 0.95 continued on next page www.recom-power.com REV.: 4/2020 L-1 O O P P E a C C R R O O Y M M n D D O O U U t C C C C E E y T T R R S SRACT12 AC/DC Converter Series Specifications (measured Ta= 25C, 240VAC, rated load unless otherwise specified) Parameter Condition Min. Typ. Max. THD full load 25% Start-up Time 500ms Internal Operating Frequency 60kHz (1) Output Ripple Current 200mA Notes: Note1: Measured at 20MHz BW by using a 12 twisted pair-wie terminated with a 0.1F and 47F capacitor parallel across output REGULATIONS Parameter Condition Value Output Accuracy 5% typ. Load Regulation 5% max. Line Regulation 5% max. PROTECTION Parameter Condition Value Input Fuse fusible resistor Short Circuit Protection (SCP) Latch OFF, auto recovery after fault condition is removed RACT12-300 50VDC max. RACT12-350 42VDC max. Latch OFF, auto recovery Over Voltage Protection (OVP) RACT12-500 30VDC max. after fault condition is removed RACT12-700 26VDC max. Over Load Protection (OLP) Latch OFF, auto recovery after fault condition is removed Over Temperature Protection (OTP) 110C Latch OFF, auto recovery after fault condition is removed Isolation Voltage I/P to O/P tested for 1 minute 3.75kVAC Leakage Current 5mA max. Maximum loading of automatic circuit breakers* * 230VAC, 1Ohm, 90 phase angle and max. load Circuit Breaker Circuit Breaker Current Typ 10A 16A 20A 25A B 36 57 69 85 C 57 87 109 134 ENVIRONMENTAL Parameter Condition Value Operating Temperature Range without derating natural convection 0.1m/s (see graph) -20C to +50C Max. Case Temperature at tc point +80C max. Operating Humidity non-condensing 5-85% RH IP Rating IP20 Pollution Degree PD2 3 RACT12-300 >40 x 10 hours Design Lifetime +25C ambient all others >30 x 10 hours continued on next page www.recom-power.com REV.: 4/2020 L-2