BD9E303EFJ-LBE2 ROHM

Datasheet 7.0V to 36V Input, 3.0A Integrated MOSFET Single Synchronous Buck DC/DC Converter BD9E303EFJ-LB General Description Key Specifications This is the product guarantees long time support in Input Voltage Range: 7.0V to 36V Industrial market.BD9E303EFJ-LB is a synchronous buck Output Voltage Range: 1.0V to VIN0.8V switching regulator with built-in power MOSFETs. It is a Output Current: 3.0A (Max) current mode control DC/DC converter and features Switching Frequency: 300kHz (Typ) high-speed transient response. Phase compensation can High-Side MOSFET ON-Resistance: 90m (Typ) also be set easily. Low-Side MOSFET ON-Resistance: 80m (Typ) Standby Current: 0A (Typ) Features Long Time Support Product for Industrial Package W (Typ) x D (Typ) x H (Max) Applications. HTSOP-J8 4.90mm x 6.00mm x 1.00mm Synchronous single DC/DC converter. Over-Current Protection. Short Circuit Protection. Thermal Shutdown Protection. Under voltage Lockout Protection. Soft Start. HTSOP-J8 package (Exposed Pad). Applications Industrial Equipment. Power supply for FAs industrial device using 24V bass. Consumer applications such as home appliance. Distribution type power supply system for 12V, and HTSOP-J8 24V. Typical Application Circuit VIN 2 VIN BOOT 1 24V BD9E303EFJ-LB 0.1F 0.1 F 10F VOUT SW 8 10H Enable 3 EN 22F2 COMP AGND PGND FB 6 4 7 5 30k 6800pF 7.5k 15k Figure 1. Application circuit Product structureSilicon monolithic integrated circuit. This product is not designed for protection against radioactive rays. www .rohm.com TSZ02201-0J3J0AJ00650-1-2 2015 ROHM Co., Ltd. All rights reserved. 1/28 TSZ2211114001 13.Feb.2015 Rev.002DatasheetDatasheet BD9E303EFJ-LB Pin Configuration (TOP VIEW) 1 8 SW BOOT VIN 2 7 PGND E-Pad 3 6 COMP EN AGND 4 5 FB Figure 2. Pin assignment Pin Description(s) Pin No Pin Name Description Connect a bootstrap capacitor of 0.1F between this terminal and SW terminal. 1 BOOT The voltage of this capacitor is the gate drive voltage of the high-side MOSFET. Power supply terminal for the switching regulator and control circuit. 2 VIN Connecting a 10F and 0.1F ceramic capacitor is recommended. Turning this terminal signal low-level (0.8V or lower) forces the device to enter the shut 3 EN down mode. Turning this terminal signal high-level (2.5V or higher) enables the device. This terminal must be terminated. 4 AGND Ground terminal for the control circuit. Inverting input node for the gm error amplifier. 5 FB See page 18 on how to calculate the resistance of the output voltage setting. Output of gm error amplifier, and input of PWM comparator. Connect phase 6 COMP compensation components to this pin. See page 20 on how to calculate the resistance and capacitance for phase compensation. 7 PGND Ground terminal for the output stage of the switching regulator. Switch node. This terminal is connected to the source of the high-side MOSFET and drain of the low-side MOSFET. Connect a bootstrap capacitor of 0.1F between this 8 SW terminal and BOOT terminal. In addition, connect an inductor considering the direct current superimposition characteristic. Exposed pad. Connecting this to the internal PCB ground plane using multiple vias - E-Pad provides excellent heat dissipation characteristics. www.rohm.com TSZ02201-0J3J0AJ00650-1-2 2015 ROHM Co., Ltd. All rights reserved. 2/28 TSZ2211115001 13.Feb.2015 Rev.002