KTR10EZPF3403 ROHM

High voltage resistance chip resistors KTR series Datasheet Features 1)Twice the rated voltage of conventional products.. 2)Perfect for use in high voltage circuit. (Camera Flash circuit, etc) 3)ROHM resistors have obtained ISO9001 / IATF16949 certification. 4)Corresponds to AEC-Q200. Products list Rated Limiting Operating Size Temperature Resistance Automotive power plement Resistance range temperature coefficient tolerance Part No. grade (70) voltage range available (mm) (inch) (W) (V) (ppm / ) (%) () () 200 F ( 1% ) 1R10 (E24/96 series) KTR03 1608 0603 0.10 350 100 F ( 1% ) 10R10M (E24/96 series) -55 +155 Yes 200 J ( 5% ) 1R10M (E24 series) 100 F ( 1% ) 1R10M (E24/96 series) KTR10 2012 0805 0.125 400 -55 +155 Yes 200 J ( 5% ) 1R30M (E24 series) 100 F ( 1% ) 1R10M (E24/96 series) KTR18 3216 1206 0.25 500 -55 +155 Yes 200 J ( 5% ) 1R10M (E24 series) 100 F ( 1% ) 1R10M (E24/96 series) Yes KTR25 3225 1210 0.33 600 -55 +155 J ( 5% ) (E24 series) 200 1R10M *E24 : Standard products, E96 : Custom products. *Design and specifications are subject to change without notice.Carefully check the specification sheet supplied with the product before using or ordering it. Part number description K T R 1 0 E Z P J 1 0 0 Resistance Part No. Size (mm inch ) Packaging specifications code Nominal resistance tolerance Resistance code, 3 or 4 digits. 03(1608 0603 ) Packaging Quantity Part No. Code F( 1% ) KTR specifications / Reel 10(2012 0805 ) J ( 5% ) (High voltage 18(3216 1206 ) Paper tape Resistance Resistance resistance KTR03 EZP 5,000 tolerance code 25(3225 1210 ) (4mm Pitch) chip resistors) F 4 digits Paper tape KTR10 EZP 5,000 3 digits (4mm Pitch) J EX.) Paper tape KTR18 EZP 5,000 (4mm Pitch) 1 = 1R00 (1%) 1R0 (5%) Embossed tape KTR25 JZP 4,000 (4mm Pitch) 10 = 10R0 (1%) 100 (5%) 1M = 1004 (1%) 105 (5%) www.rohm.com 1/4 2020 ROHM Co., Ltd. All rights reserved. 2020.07 - Rev.GKTR series Datasheet Chip resistor dimensions and markings KTR03 KTR10/18/25 <Marking method> There are three or four digits used for the calculation number according to IEC code and is used for the decimal point. (Unit:mm) Marking Part No. (mm) (inch) L W t a b existence No* KTR03 1608 0603 1.600.10 0.800.10 0.450.10 0.300.20 0.300.20 KTR10 2012 0805 2.000.10 1.250.10 0.550.10 0.300.20 0.400.20 Yes Yes KTR18 3216 1206 3.200.15 1.600.15 0.550.10 0.300.25 0.500.25 KTR25 3225 1210 3.200.15 2.500.15 0.550.10 0.300.25 0.500.25 Yes *Only with square mark Land pattern example (Unit:mm) Dimensions A B C D Part No. KTR03 1.0 2.0 0.8 0.5 KTR10 1.2 2.6 1.15 0.7 KTR18 2.2 4.0 1.5 0.9 KTR25 2.2 4.0 2.3 0.9 www.rohm.com 2/4 2020 ROHM Co., Ltd. All rights reserved. 2020.07 - Rev.G