LTR18EZPF49R9 ROHM

High power chip resistors < Wide terminal type > LTR series Datasheet Features 1)High joint reliability with long side terminations. 2)Highest power ratings in their class. 3)Guaranteed anti-surge characteristic in all series. 4)ROHM resistors have obtained ISO9001 / ISO / TS16949 certification. 5)Corresponds to AEC-Q200. Products list Rated Limiting Maximum Operating Size Temperature Resistance Part No. power element overload Resistance range temperature coefficient tolerance (70) voltage voltage range (mm) (inch) (W) (V) (V) (ppm / ) (%) () () 100 D ( 0.5% ) 10R1M (E24/96 series) LTR10 2012 0805 0.25 150 300 100 F ( 1% ) 1R1M (E24 series) -55 +155 200 J ( 5% ) 1R1M (E24 series) 100 D ( 0.5% ) 10R1M (E24/96 series) LTR18 3216 1206 0.75 200 400 100 F ( 1% ) 1R1M (E24 series) -55 +155 200 J ( 5% ) 1R1M (E24 series) 100 D ( 0.5% ) 10R130k (E24 series) LTR50 5025 2010 1.0 200 400 100 F ( 1% ) 1R1M (E24 series) -55 +155 200 J ( 5% ) 1R1M (E24 series) 100 D ( 0.5% ) 10R1M (E24 series) LTR100 6432 2512 2.0 200 400 100 F ( 1% ) 1R1M (E24 series) -55 +155 J ( 5% ) (E24 series) 200 1R<1M *E24 : Standard products, E96 : Custom products.(Class J is E24 series only) Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with the product before using or ordering it. Part Number Description L T R 1 8 E Z P J 1 0 5 Resistance Part No. Size (mm inch ) Packaging specifications code Nominal resistance tolerance 10(2012 0805 ) Packaging Quantity D (0.5%) Resistance code, 3 or 4 digits. Part No. Code LTR specifications / Reel F (1%) 18(3216 1206 ) Resistance Resistance (High power J (5%) tolerance code 50(5025 2010 ) Paper tape chip resistors LTR10 EZP 5,000 4 digits 100(6432 2512 ) (4mm Pitch) D,F / wide terminal 3 digits J Paper tape type) LTR18 EZP 5,000 (4mm Pitch) EX.) Embossed tape 1 = 1R00 (1%) LTR50 UZP 5,000 (4mm Pitch) 1R0 (5%) Embossed tape 9.1 = 9R10 (1%) LTR100 JZP 4,000 (4mm Pitch) 9R0 (5%) 10 = 10R0 (0.5%, 1%) 100 (5%) 1M = 1004 (0.5%, 1%) 105 (5%) www.rohm.com 1/4 2016 ROHM Co., Ltd. All rights reserved. 2017.06 - Rev.HLTR series Datasheet Chip resistor dimensions and markings <Marking method> There are three or four digits used for the calculation number according to IEC code and is used for the decimal point. (Unit:mm) Marking Part No. (mm) (inch) L W t a b existence LTR10 2012 0805 1.200.10 2.00.10 0.550.10 0.250.10 0.350.20 Yes LTR18 3216 1206 1.60.15 3.20.15 0.550.10 0.300.20 0.500.20 Yes LTR50 5025 2010 2.50.15 5.00.15 0.550.10 0.380.20 0.900.20 Yes No LTR100 6432 2512 3.20.15 6.40.15 0.550.15 0.400.25 1.130.25 Land pattern example (Unit:mm) Dimensions A B C D Part No. LTR10 0.50 2.70 2.00 1.10 LTR18 0.60 2.90 3.20 1.15 LTR50 0.75 3.35 5.00 1.30 LTR100 0.83 3.69 6.40 1.43 www.rohm.com 2/4 2016 ROHM Co., Ltd. All rights reserved. 2017.06 - Rev.H