Taper and deburring countersinkers Taper and deburring countersinkers DIN 335 type C 90 HSS Co 5 CBN ground for stainless steel Counters. angle: 90 Because of the CBN deep-ground flutes the Shank: cylindrical cutting edges are extremely sharp. Ideal for Cutting edges: 3 burr- and chatter-free deburring and counter- 1.5 1.5 Surface: bright sinking. Applicable for special steel, stainless Right-hand cutting and acidresistant steel. Best results at low cutting speeds. Packing unit: d2 in plastic tubes of 1 Countersinker Total Shank Countersinkings as per Article no. Price nominal d3 length d2 DIN 74 each d1 mm mm L mm mm AF BF 6,3 1,5 45,0 5,0 M 3 102 107 E 8,0 2,0 50,0 6,0 M 4 102 110 E 8,3 2,0 50,0 6,0 M 4 102 111 E 10,0 2,5 50,0 6,0 M 5 102 113 E 10,4 2,5 50,0 6,0 M 5 102 114 E 12,4 2,8 56,0 8,0 M 6 102 116 E 16,5 3,2 60,0 8,0 M 8 102 119 E 16,5 3,2 60,0 10,0 M 8 102 119-1 E 20,5 3,5 63,0 10,0 M 10 102 121 E 25,0 3,8 67,0 10,0 M 12 102 123 E d3 31,0 4,2 71,0 12,0 M 16 102 125 E d1 Taper and deburring countersinkers DIN 335 type C 90 tungsten carbide K 20 Counters. angle: 90 Because of the deep-ground flutes the cutting Shank: cylindrical edges are absolutely sharp. Ideal for burr- and Cutting edges: 3 chatter-free deburring and countersinking. Ap- Surface: bright plicable for abrasive and hard steel over 1000 Right-hand cutting N/mm consistency, GG over 240 HB. d2 Packing unit: in plastic tubes of 1 Countersinker Total Shank Countersinkings as per Article no. Price nominal d3 length d2 DIN 74 each d1 mm mm L mm mm AF BF 6,3 1,5 45,0 5,0 M 3 102 261 8,3 2,0 50,0 6,0 M 4 102 262 10,4 2,5 50,0 6,0 M 5 102 263 12,4 2,8 56,0 8,0 M 6 102 264 16,5 3,2 60,0 10,0 M 8 102 265 20,5 3,5 63,0 10,0 M 10 102 266 25,0 3,8 67,0 10,0 M 12 102 267 d3 31,0 4,2 71,0 12,0 M 16 102 268 d1 Modifications of tungsten carbide quality reserved. - 69 - L LX-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for ruko manufacturer: Other Similar products are found below : 214214 214043 214017 202040E 208040 214049 214053 214217 101021 101062 232-040 102146 102303E 101051 242-207 102411 107015 245001 242-205 116048 102771 102785 244201 244202 A215214RO A215215RO 217-020 214057 202033E 202030E 214020 214044 214096 215030 232025 102302E 237-030 102114E A214215RO 217-315 214100 214047 208050 214062 214140 214150 230025 241 001 241-010 241-100