10LPCV2475 Sensata

Control Relays DataSheet LPCV Series Linear proportional controller Ratings from 15A to 110A 240 VAC 0-5 V DC, 0-10 V DC, or 4-20mA input For use with resistive loads only PRODUCT SELECTION 15 A Description 25 A 40 A 75 A 110 A 5LPCV2415 5LPCV2425 5LPCV24110 0-5 VDC Control 5LPCV2440 5LPCV2475 0-10 VDC Control 10LPCV2415 10LPCV2425 10LPCV2440 10LPCV2475 10LPCV24110 20LPCV2415 20LPCV2425 4-20 mA Control 20LPCV2440 20LPCV2475 20LPCV24110 (1) OUTPUT SPECIFICATIONS (voltage) Description 240 VAC Operating Voltage (60Hz) Vrms 20-300 Transient Overvoltage Vpk 600 Maximum Off-State Leakage Current Rated Voltage mArms 10 Minimum Off-State dv/dt Maximum Rated Voltage V/sec 200 (1) OUTPUT SPECIFICATIONS (current) Description 15 A 25 A 40 A 75 A 110 A Maximum Load Current Arms 15 25 40 75 110 Minimum Load Current Arms 0.10 0.10 0.10 0.15 0.20 Maximum Surge Current (16.6ms) Apk 150 250 625 1000 1500 Maximum On-State Voltage Drop Rated Current Vpk 1.6 1.6 1.6 1.6 1.6 1.48 Thermal Resistance Junction to Case (Rjc) C/W 1.02 0.31 0.63 0.28 94 260 4150 Maximum I t for Fusing (8.3 msec) A sec 1620 9340 0.5 0.5 0.5 Minimum Power Factor (with Maximum Load) 0.5 0.5 (1) INPUT SPECIFICATIONS Description 10LPCV 20LPCV 5LPCV Control Voltage Range 0-5 VDC 0-10 VDC 4-20 mA Control Range Limits (Min/Msx) -1.0/20 VDC -0.5/25 mA -0.5/10 VDC Turn-On Threshold 0.25 VDC 0.5 VDC 4.5 mA Nominal Input Impedance 12.7K Ohm 25 K Ohm 460 Ohm Sync Voltage (terminal 6 and 7) 16-24 VAC 16-24 VAC 16-24 VAC (4) POWER SUPPLY SPECIFICATION Description PS240 PS120 Input Voltage 50/60Hz 120 VAC 240 VAC Output Voltage 50/60Hz (Sync Voltage) 20 VAC/100mA 20 VAC/100mA Ambient Operating Temperature Range -30 to 80C -30 to 80C Ambient Storage Temperature Range -40 to 125C -40 to 125C 6-32 Screws, .25 Fastons Terminals Screw Torque Requirement 6-32 Screws -10 in lbs. Weight (typical) 8.6 oz. (245g) Do not forget to visit us at: www.crydom.com Copyright 2017 Crydom Inc. Specifications subject to change without notice.Control Relays DataSheet GENERAL SPECIFICATIONS Description Dielectric Strength, signal to load 2500 Vrms Dielectric Strength, signal to Base 2500 Vrms Ambient Operating Temperature Range -30 to 80C Ambient Storage Temperature Range -40 to 125C Weight (typical) 6.0 oz. (175g) Encapsulation Themally Conductive Epoxy Terminals 8-32 Screws, .25 Fastons Screw Torque Requirement 8-32 and 10-32 Screws - 20in. lbs. GENERAL NOTES 1) All parameters at 25C unless otherwise specied. 2) Linear taper potentiometer 1-10K Ohm, watt. 3) 50Hz models available. 4) 20 VAC must be in phase with load WIRING DIAGRAM Tolerances: 0.02 in / 0.5 mm All dimensions are in: inches millimeters 1.35 Max. 2.21 (40.6) 2.00 2.10 (56.1) (50.8) (53.3) 1.05 1.52 .12 (26.7) 1.00 (38.6) (3.0) (25.4) 8-32 TERMINALS OUTPUT (2 PLACES) 2.21 2.62 2.50 1.00 PROPORTIONAL CONTROLLER 2.25 (56.1) (66.5) (63.5) (25.4) (57.2) .250 FASTON TERMINALS (5 PLACES) .12 6-32 TERMINALS .30 Typ MOUNTING SLOT (3.0) (2 PLACES) (7.6) .250 FASTON 0.17 (4.3) DIA62 PS120/PS240 1.60 Max. TERMINALS (15.7) (40.6) (2 PLACES) Firing Angle vs. Input Signal (20 mA) 10V 5V 7.5V Sync Voltage 5V 2.5V 20 Vac from Power 4 Supply Module 12Vdc Output PS-120 (120Vac) For Manual Control 2.5V - + PS-240 (240Vac) 5 4 3 From Control Note: Not Used 4 See note 2 (4 mA) 0V 0V 0-5 Vdc if Conneced to Voltage range: 16-24Vac 180 135 90 45 0 0-10 Vdc Analog Card 4-20 mA Do not forget to visit us at: www.crydom.com Copyright 2017 Crydom Inc. Specifications subject to change without notice.