ELECTRICAL SPECIFICATIONS OPTICAL ISOLATOR POWER: The optical isolator can accommodate standard operating ELECTRONIC MODULE voltages from 5 to 28 VDC. It should never be connected directly to AC power mains. The module draws approximately 75 mA and a green LED indicates the unit is powered. The optical isolator module does not provide power to the encoder. Any encoders used in conjunction with this module must be connected to their own power. SIGNAL: Specifying an optical isolator module requires knowledge of three system parameters: the DC supply voltage available in the system the encoder output type (logic levels and driver type) and the input signal specifications of the receiving electronics. MECHANICAL SPECIFICATIONS Package dimensions are 114.4 mm high by 99 mm wide by 22.5 mm thick. The package mounts to a DIN rail type EN 50 022 (35mm X 7.5mm). A length of DIN rail is supplied with each module. The module simply snaps directly to the DIN rail and is ready to use. This is a versatile interface between an incremental encoder and receiving electronics. It accepts single ended or differential inputs and provides single ended or differential outputs in either an open collector or line driver configuration. It accommodates all standard operating voltages from 5 to 28 VDC. Up to eight Optical Isolator Modules can be daisy-chained to provide multiple, simultaneous outputs to controllers or PLCs. This Optical Isolator can help clean up noisy signals by converting to a different line driver output. It has a 1 MHz throughput capability and can be used wherever a fast, optically isolated interface is required. Output Code Format Dual Channel in quadrature plus index and complements. Data lines are designated A, B, Z, A/, B/, Z/ at the From Encoder module Differential line driver (Use Connection Instructions 1) Single ended line driver (Use Connection Instructions 2) Output Signal Type From Encoder Single ended open collector with pull-up resistors internal to encoder (Use Connection Instructions 3) Single ended, open collector (Use Connection Instructions 3) 3 VDC Output Signal 5 VDC (TTL, RS422 compatible, line driver) Voltage Level From 12-15 VDC Encoder 24VDC Frequency Response 1 MHz, maximum of Optical Isolator Power Requirements 5-28 VDC 5%, 75mA plus load current For Optical Isolator 28V/V Line Driver, 100mA source/sink, Vout = Vin Optical Isolator 28V/5 Line Driver, 100mA source/sink, Vout = 5V (Derate output current to 50mA with supply voltage > 12VDC) Output Options 28V/OC NPN Open Collector, 80mA sink Protection Level Supply lines protected against over voltage to 60 volts and reverse voltage Tristate Outputs Available as S Special Feature Tel: 805-716-0322 Fax: 805-968-3154 1461 Lawrence Drive, Thousand Oaks, CA 91320, USA www.beisensors.com Specification No. 02125-001 Rev 1117 CONNECTION INSTRUCTIONS 1 Differential Line Driver Encoder signals from 5 VDC to 24 VDC (must specify the voltage when ordering) This is the preferred type of encoder output as it has the best noise immunity. Connect each encoder signal to its like optical isolator input (A to A, A/ to A/, etc). Figure 1 Standard Connection to Optical Isolator Optical Isolator Module Z Z/ AA A No Connection A A/ A/ A/ No Connection A/ ENCODER B B B B B/ B/ B/ B/ B/ Z Z B CONTROLLER Z Z/ Z/ Z Z/ A/ Z/ VS REG Vs, 5V to 28V 0V 0V, Power Common +V +V A 0V 0V Encoder Differential Line Driver Output CONNECTION INSTRUCTIONS 2 Single Ended Line Driver Encoder signal from 5 VDC to 24 VDC (must specify the voltage when ordering) Connect encoder output A to optical isolator module input channel A, B to B and Z to Z. Connect the A/, B/, and Z/ inputs of the optical isolator to circuit common of the encoder supply. Single ended operation is limited to shorter cable runs and is more susceptible to noise. Figure 2 Connection Diagram Single Ended Line Driver Z Optical Isolator No Connection AA A No Connection A A/ A/ A/ Connect A/, B/, Z/ to Encoder Circuit B B Common B B B/ ENCODER B/ B/ Z Z B CONTROLLER Z Z/ Z/ Z VS Z/ REG A Vs, 5V to 28V 0V 0V, Power Common +V +V Encoder 0V Supply 0V Encoder Single Ended Line Driver Output Tel: 805-716-0322 Fax: 805-968-3154 1461 Lawrence Drive, Thousand Oaks, CA 91320, USA www.beisensors.com Specification No. 02125-001 Rev 1117