GN050DSR Sensata

Panel Mount Datasheet GN0 Series Three-phase Motor Reversing solid-state relay Ratings of 25A and 50A per phase 48-530 VAC SCR output for heavy industrial loads DC control LED input status indicator UL508 Endurance Rating UL/CSA/TUV Approved, CE Compliant to EN60950-1 PRODUCT SELECTION Control Voltage 25A 50A 4-32 VDC GN025DSR GN050DSR OUTPUT SPECIFICATIONS (1) Description 25A 50A Operating Voltage (47-63Hz) Vrms 48-530 48-530 Maximum Load Current Arms (2) 25 50 Transient Overvoltage Vpk 1100 1100 Maximum Off-State Leakage Current Rated Voltage mArms (3) 6 6 Minimum Load Current mArms 0.1 0.1 475 / 500 710 / 750 Maximum Surge Current 50/60 Hz (1 cycle) Apk 1 Second Surge Current 50/60 Hz Apk 100 150 Maximum On-State Voltage Drop Rated Current Vpk 1.35 1.35 Maximum IT for Fusing (50/60 Hz, 1/2 cycle) A sec 1130 / 1030 2520 / 2320 Thermal Resistance Junction to Case (Rjc) C/W 0.26 0.25 Minimum Off-State dv/dt Maximum Rated Voltage V/sec (4) 500 500 HP Ratings at 120V / FLC Arms 0.75 / 6.4 1.5 / 12 HP Ratings at 240V / FLC Arms 1 / 4.2 3 / 9.6 HP Ratings at 480V / FLC Arms 3 / 4.8 7.5 / 11 HP Ratings at 600V / FLC Arms 5 / 6.1 10 / 11 INPUT SPECIFICATIONS (1) Description Parameters Control Voltage Range 4.0-32 VDC Minimum Turn-On Voltage 4.0 VDC Must Turn-Off Voltage 1.0 VDC Maximum input current 35 mA Minimum input current (for on-state) 23 mA Input Resistance Current Regulated Turn-On Time msec 150 Turn-Off Time msec 8.33 Interlocking Time msec 100 Do not forget to visit us at: www.crydom.com Copyright 2016 Crydom Inc. Specifications subject to change without notice.Panel Mount Datasheet GENERAL SPECIFICATIONS Description Parameters Input to output isolation 4000 Vrms Input/Output to ground isolation 2500 Vrms Maximum Capacitance, Input/Output 8 pF Ambient Operating Temperature Range -40C to 80C Ambient Storage Temperature Range -40C to 100C Weight (typical) 13.1 oz (370 g) Housing Material UL 94V0 (self extinguishing) Input Terminal Screw Torque Range in-lb/Nm 16.8/1.9 Output Terminal Screw Torque Range in-lb/Nm 21.2/2.4 GENERAL NOTES 1) All parameters at 25C unless otherwise specied. 2) When mounted to the proper size heat sink (see derating curves) 3) Measured between 1/L1 and 2/T1 or 3/L2 and 4/T2 4) Off-State dv/dt test method per EIA/NARM standard RS-443, paragraph 13.11.1 MECHANICAL SPECIFICATIONS Tolerances: 0.02 in / 0.5 mm All dimensions are in: inches millimeters 3.99 101.3 3.62 92.0 3/L2 1/L1 1.87 47.6 3.14 79.7 0.2 5.1 4/T2 2/T1 1.39 35.4 4.09 103.9 Do not forget to visit us at: www.crydom.com Copyright 2016 Crydom Inc. Specifications subject to change without notice.