SMR4825-6 Sensata

SMR48 -6 Series System monitoring solid-state relay Ratings from 25A to 90A 60-280 V AC DC control LED status indicators Alarm output signal Inverting or non-inverting input Normally open or normally closed alarm output PRODUCT SELECTION Control Voltage 25A 50A 90A 8-32 VDC SMR4825-6 SMR4850-6 SMR4890-6 AVAILABLE OPTIONS OUTPUT SPECIFICATIONS (1) Description SMR4825-6 SMR4850-6 SMR4890-6 Operating Voltage (47-63Hz) Vrms 96-530 96-530 96-530 Transient Overvoltage Vpk 1200 1200 1200 Maximum Off-State Leakage Current Rated Voltage mArms 10 10 10 Minimum Off-State dv/dt Maximum Rated Voltage V/sec (2) 500 500 500 Maximum Load Current (3) Arms 25 50 90 Minimum Load Current mArms 40 40 40 Maximum 1 Cycle Surge Current (50/60Hz) Apk 239/250 597/625 1145/1200 Maximum On-State Voltage Drop Rated Current Vpk 1.6 1.6 1.6 Thermal Resistance Junction to Case (Rjc) C/W 1.02 0.63 0.28 Maximum 1/2 Cycle It for Fusing (50/60 Hz) A sec 285/259 1779/1621 6560/5976 Minimum Power Factor (with Maximum Load) 0.5 0.5 0.5 CONTROL SPECIFICATIONS (1)(4) Description INVERTING NON-INVERTING Logic Supply Voltage Range 8-32 VDC (pin 3) 8-32 VDC (pin 3) Logic Supply Current 12 8 mA 14 mA (plus pin 8 loading) Input-On Voltage Range 8-32 VDC (pin 6) 0-1.0 VDC (pin 5) Input-Off Voltage Range 0-0.4 VDC (pin 6) 8-32 VDC (pin 5) Input-On Current 12 VDC Logic Supply 6 mA 1.0 mA Maximum Turn-On Time msec 1/2 Cycle 1/2 Cycle Maximum Turn-Off Time msec 1/2 Cycle 1/2 CycleALARM SPECIFICATIONS (1)(4) Description NORMALLY CLOSED NORMALLY OPEN Alarm-On VoltageSupply Voltage (with load) Open Col. NPN (pin 7Supply Voltage (minus 1.0 V) Active High PNP (pin 8 Alarm-Off Voltage1.5 VDC Active Low NPN (pin 70.0 VDC (with load) Open Col. PNP (pin 8 Maximum Alarm Output Current 100 mA 100 mA Alarm Delay (Min.-Max.) 30-100 msec 30-100 msec GENERAL SPECIFICATIONS Description Parameters Dielectric Strength, Input/Output/Base (50/60Hz) 4000 Vrms 9 Minimum Insulation Resistance ( 500 VDC) 10 Ohm Maximum Capacitance, Input/Output 8 pF Ambient Operating Temperature Range -40 to 80C Ambient Storage Temperature Range -40 to 125 C Weight (typical) 3.0 oz (86.5g) Encapsulation Thermally conductive Epoxy Output Terminals: Screws and Saddle Clamps Furnished, Unmounted Input Connector (locking): ITW Pancon No. MTSS100-6 or Equivalent Mating Connector (supplied): ITW Pancon No. CT100F22-6 or Equivalent Recommended Terminal Screw Torque Range: 8-32 & 10-32 Screws - 20 in. lbs. (Screws dry without grease) GENERAL NOTES GENERAL NOTES 1) All parameters at 25C unless otherwise specified. 2) Off-State dv/dt test method per EIA/NARM standard RS-443, paragraph 13.11.1 3) Heat sinking required, for derating curves see page 2. 4) All voltages are positive in respect to common (pin 4) MECHANICAL SPECIFICATIONS