S2S3 Series V : 600V, Non-zero cross type DRM S2S3 Series Mini-Flat Package Zero cross type is also available. (S2S4 Series) Phototriac Coupler for triggering Description Agency approvals/Compliance S2S3 Series Phototriac Coupler include an infrared 1. Recognized by UL1577 (Double protection isolation), emitting diode (IRED) optically coupled to an output file No. E64380 (as model No. S2S3) Phototriac. 2. Approved by CSA, file No. CA95323 (as model No. These devices feature full wave control and are S2S3) ( ) ideal isolated drivers for medium to high current Triacs. 3. Optionary available VDE Approved (DIN EN SOP package provides 3.75kV isolation from input 60747-5-2), file No. 40009162 (as model No. S2S3) to output with superior commutative noise immunity. 4. Package resin : UL flammability grade (94V-0) () DIN EN60747-5-2 : successor standard of DIN VDE0884. Up to Date codeR (December 2003), approval of DIN Features VDE0884. From Date codeS1 (January 2004), approval of DIN 1. High repetitive peak off-state voltage (V : 600V) DRM EN60747-5-2. () 2. Non-zero crossing functionality Reinforced insulation type is also available. (PC3SG11YIZ Series) 3. I ranks available (see Model Line-up section in this FT datasheet) 4. 4pin Mini-flat package Applications 5. Superior noise immunity (dV/dt : MIN. 100V/s) 1. Triggering for Triacs used to switch on and off 6. Double transfer mold construction (Ideal for Flow devices which require AC Loads. Soldering) For example heaters, fans, motors, solenoids, and 7. High isolation voltage between input and output valves. (Viso(rms) : 3.75kV) 2. Triggering for Triacs used for implementing phase control in applications such as lighting control and temperature control (HVAC). 3. AC line control in power supply applications. Notice The content of data sheet is subject to change without prior notice. In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. Sheet No.: D2-A06501FEN 1 Date Mar. 31. 2004 SHARP CorporationS2S3 Series Internal Connection Diagram 1 Anode 1 4 2 Cathode 3 Anode/Cathode 4 Cathode/Anode 2 3 (Unit : mm) Outline Dimensions VDE option 0.3 0.3 3.6 3.6 0.25 0.25 2.54 2.54 4 3 4 3 Date code (2 digit) Date code (2 digit) SHARP SHARP mark mark Model No. Model No. Anode Anode mark mark 2S3 2S3 4 Factory identification mark Factory identification mark 0.1 0.1 1 2 1 2 0.4 0.4 VDE identification mark 0.3 5.3 Epoxy resin 0.3 5.3 Epoxy resin 45 45 +0.4 0.5 0.2 +0.4 +0.2 0.5 0.2 7.0 0.7 +0.2 7.0 0.7 Product mass : approx. 0.09g Product mass : approx. 0.09g Sheet No.: D2-A06501FEN 2 6 6 0.1 0.2 0.1 2.6 0.05 0.2 4.4 0.2 0.1 0.2 0.1 2.6 0.2 0.05 0.2 4.4