DATA SHEET OLS910: Hermetic Surface-Mount Photovoltaic Optocoupler Features Performance guaranteed over -55 C to +125 C ambient temperature range 1500 VDC electrical isolation High open-circuit voltage High short-circuit current Small hermetic surface mount package High reliability and rugged construction Isolated voltage source Offers 100% high reliability screenings Figure 1. OLS910 Block Diagram Description The OLS910 consists of a pair of LEDs that are optically coupled Figure 1 shows the OLS910 functional block diagram. Table 1 to a dielectrically isolated photovoltaic diode array, packaged in a provides the OLS910 absolute maximum ratings. Table 2 provides small hermetic Leadless Chip Carrier (LCC). When the LED is the OLS910 electrical specifications. energized, the infrared emission is detected by the photovoltaic array and a DC output voltage is generated. This electrically Figures 2 through 6 illustrate the OLS910 typical performance isolated voltage can be used to drive the gates of Metal Oxide characteristics. Figure 7 shows the OLS910 package dimensions. Semiconductor (MOS) devices. Device mounting is achieved with reflow soldering or conductive epoxies. Phone 408 946-1968 Fax 408 946-1960 hirel.sales skyworksinc.com www.skyworksinc.com 202346F Isolink Proprietary Information Products and Product Information are Subject to Change Without Notice May 13, 2019 1 DATA SHEET OLS910: HERMETIC SURFACE-MOUNT PHOTOVOLTAIC OPTOCOUPLER 1 Table 1. OLS910 Absolute Maximum Ratings Parameter Symbol Minimum Maximum Units Coupled Input to output isolation voltage VDC -1500 +1500 V Storage temperature range TSTG -65 +150 C Operating temperature range TA -55 +125 C Mounting temperature range (3 minutes maximum) +240 C Input Diode Average input current IDD 50 mA Peak forward current (1 ms duration) IF 100 mA Reverse voltage VR 5 V Power dissipation PD 100 mW Output Detector Forward voltage VF 20 V Reverse voltage VR 200 V 1 Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to the device with only one parameter set at the limit and all other parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device. CAUTION: Although this device is designed to be as robust as possible, electrostatic discharge (ESD) can damage this device. This device must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times. 1 Table 2. OLS910 Electrical Specifications (TA = -55 C to +125 C, Unless Otherwise Noted) Parameter Symbol Test Condition Minimum Typical Maximum Units Open circuit voltage VOC IF = 10.0 mA 7.5 13.0 V Short circuit current ISC IF = 10 mA -7 -20 A Input: Forward voltage VF If = 10 mA, TA = 25 C 2.4 2.8 3.2 V If = +10 mA, TA = -55 C +2.8 +3.6 V If = 10 mA, TA = 125 C 2.2 3.0 V Reverse breakdown voltage BvR IR = 10 A 5 V 2 Output leakage current II O RH 50%, 1500 VDC, TA = 25 C, Duration = 1 s 1 A Time: IF = 10 mA, PW = 100 s, f = 1 kHz, C = 15 pf, TA = 25 C, RL = 10 M Turn on tON tON = 0 V to 90% 60 s Turn off tOFF tOFF = VOC to 10% 400 s 1 Performance is guaranteed only under the conditions listed in the above table. 2 Measured between pins 1, 2, and 6 shorted together, and pins 3, 4, and 5 shorted together. TA = 25C and duration = 1 s. Phone 408 946-1968 Fax 408 946-1960 hirel.sales skyworksinc.com www.skyworksinc.com 2 May 13, 2019 Isolink Proprietary Information Products and Product Information are Subject to Change Without Notice 202346F