01821.0-00

FF 01821 Outdoor Filter Fan 14 cfm Quick and easy filter change Lockable outer door Impact resistant Weather and UV resistant This filter fan can be used in outdoor enclosures where warm air has to be dissipated. To clean and exchange the filter mat, it is only necessary to open the lockable door of the outdoor hood eliminating the need to allow interior access to the enclosure. A protection type of IP55 is achieved due to the special design of the hood and the use of fine filter mats. The plastic used for the hood of this filter fan is highly weather and UV light resistant. Outdoor Filter Fan 6.5 (165 mm) 2.4 (62 mm) 2.6 (65 mm) Technical Data Axial fan, ball bearing service life min. 50,000h at 77F (25C) and 65% RH aluminum fan body, plastic rotor Connection 2 wires w/ cage clamps, AWG 14 (2.5mm), length 4 (100mm) Filter fan and exhaust filter housing high impact ASA plastic, light grey 0.7 +0.2 5.6 (142 mm) (18 mm) burning behavior according to UL 94H-B high resistance to weather and UV light Mounting frame with double-sided industrial adhesive for mounting to the outside of enclosure certain operating circumstances may make the additional use of screws necessary cut-out template included Filter media rating F5 acc. to DIN EN 779, filtering degree 98% Filter material synthetic fiber with progressive construction, temperature View from rear Outdoor Exhaust Filter resistant to 212F, self-extinguishing class F1 5.4 (137 mm) moisture resistant to 100% RH Operating / Storage temperature +14 to +158F (-10 to +70C) / -40 to +158F (-40 to +70C) Protection class I (grounded) Drilling template for Protection type IP55 mounting frame Note: EMC version and other voltages are available upon request 0.12 (3 mm) The hood is attached permanently to the enclosure from the inside using provided screws. Filter mats can be easily changed from outside the enclosure through the lockable door in the hood. FF 01821 Outdoor Filter Fan Operating Power Average noise level Enclosure Weight Air volume, Part No. Mounting depth Approvals free blowing voltage consumption (DIN EN ISO 4871) cut-out (approx.) 1) 01821.0-00 230VAC, 50Hz 12 cfm (20m/h) 15W 40dB (A) 2.4 (62mm) 4.9 x 4.9 2.6 lbs. (1.2kg) UL File No. E234324 01821.0-02 120VAC, 60Hz 14 cfm (23m/h) 15W 40dB (A) 2.4 (62mm) 4.9 x 4.9 2.6 lbs. (1.2kg) UL File No. E234324 1) air volume increases by 15% when operating 230VAC filter fans at 60Hz EF 11821 Exhaust Filter Part No. Mounting depth Enclosure cut-out Weight (approx.) Filter mat Protection type 11821.0-00 0.6 (16mm) 4.9 x 4.9 1.6 lbs. (0.6kg) F5 acc. to DIN EN 779, filtering degree 98% IP55 FFM 086 Filter Mats Filter mat 4.6 x 4.6 (118 x 118mm) F5 (1 packing unit = 3 pcs.) Part No. 08604.0-00 Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application. STEGO, Inc. 1395 South Marietta Parkway Building 800 Marietta, GA 30067 Tel: (770) 984-0858 Fax: (770) 984-0615 Toll free: 1-888-783-4611 (US & Canada only) www.stegousa.com 5.4 (137 mm) 8.8 (224 mm) +0.2 7.3 (185 mm) 4.9 (125 mm) FF01821/2-11/US VentilatingX-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for Stego manufacturer: Other Similar products are found below : 01803.0-00 01870.0-30 01874.0-30 11882.0-30 14005.0-00 01805.0-00 01883.0-00 01925.0-00 02820.0-06 03504.0-00 11872.0-00 02541.1-03-0003 03082.0-01 03083.0-01 03209.9-00 03082.0-00 03084.0-00 01131.2-01 01170.9-00 01190.0-00 28410.0-00 02032.0-00 02540.1-13 03502.0-01 01131.9-00 08605.0-00 03114.0-00 01871.1-30 01925.1-01 12101.0-30 01163.0-01 01163.0-03 01164.0-00 01170.0-01 01170.9-01 08601.0-00 01351.0-00 01872.0-30 01131.0-00 01350.0-00 14003.0-00 02821.0-06 03503.0-00 02701.0-00 11803.0-00 11873.0-00 01131.2-00 01231.1-00 244356 04007.0-00