EV-VND7030AJ STMicroelectronics

EV-VND7030AJ VND7030AJ evaluation board Data brief Diagnostic functions Multiplexed analog feedback of: load current with high precision proportional current mirror, V supply voltage and CC T device temperature CHIP Overload and short to ground (power limitation) indication Thermal shutdown indication OFF-state open-load detection Output short to V detection CC Sense enable/disable Protections Undervoltage shutdown Features Overvoltage clamp Max transient supply voltage V 40 V CC Load current limitation Self limiting of fast thermal transients Operating voltage range V 4 to 28 V CC Configurable latch-off on Typ. on-state resistance (per Ch) R 31 m ON overtemperature or power limitation with dedicated fault reset pin Current limitation (typ) I 56 A LIMH Loss of ground and loss of V CC Stand-by current (max) I 0.5 A STBY Reverse battery with external components Electrostatic discharge protection Simple single IC application board dedicated for VND7030AJ Applications Provides electrical connectivity and thermal heat-sinking for easy prototyping Typical applications are all types of automotive General device features resistive, inductive and capacitive loads. Double channel smart high-side driver Table 1: Device summary with MultiSense analog feedback Order code Reference Very low standby current Compatible with 3 V and 5 V CMOS EV-VND7030AJ VND7030AJ evaluation board outputs September 2015 DocID026359 Rev 3 1/7 www.st.com Description EV-VND7030AJ 1 Description This board provides you an easy way to connect STMicroelectronics VIPower M0-7 technology into your existing system. The board comes pre-assembled with VND7030AJ high-side driver. On board minimum set of electrical components (as for device datasheet recommendation) is enabling the user to directly connect the load, the power supply and the microcontroller without any additional effort in external component design and connection. The VND7030AJ is a double channel high-side driver manufactured using ST proprietary VIPower technology and housed in PowerSSO-16 package. The device is designed to drive 12 V automotive grounded loads through a 3 V and 5 V CMOS-compatible interface and to provide protection and diagnostics. The device integrates advanced protective functions such as load current limitation, overload active management by power limitation and overtemperature shutdown with configurable latch-off. A FaultRST pin unlatches the output in case of fault or disables the latch-off functionality. A dedicated multifunction multiplexed analog output pin delivers sophisticated diagnostic functions including high precision proportional load current sense, supply voltage feedback and chip temperature sense, in addition to the detection of overload and short circuit to ground, short to V and OFF-state open-load. A sense enable pin allows OFF-state CC diagnosis to be disabled during the module low-power mode as well as external sense resistor sharing among similar devices. Figure 1: Evaluation board schematic Vbat Vbat J1 C1 100nF In PullU P PGND J2 Vbat R UP1 R UP2 U1 J3 IN0 R1 15K 1 INPUT0 1 IN1 R2 15K 8 16 Out0 INPUT1 OUTPUT0 2 15 OUTPUT0 3 14 R3 15K OUTPUT0 4 FaultRS T 2 13 In PullU P FaultRS T OUTPUT0 5 R4 15K +5V 6 S EN 3 FaultRS T R5 15K SEn 7 MultiSense 7 12 Out1 MultiSense MultiSense OUTPUT1 8 11 S EN C3 OUTPUT1 9 1 10 SEL0 10nF R6 15K OUTPUT1 10 SEL0 5 9 SEL1 Rsense TP1 SEL0 OUTPUT1 11 SEL1 6 SEL1 12 IN0 1 R7 15K PGND 13 4 IN1 GND 14 TP2 PGND 15 PSS0-16 16 D1 R8 17 4K7 18 ES1D L CON18 PGND LED1 LED2 C4 C2 10nF 10nF R9 R10 2k2 2k2 PGND J4 PGND PGND GAPG1704141132CFT 2/7 DocID026359 Rev 3 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 10 10 0 VBATT 1 2