LCP12-150B1RL STMicroelectronics

LCP12 Protection IC for ringing SLICs Datasheet production data Description The LCP12 has been developed to protect SLICs operating on both negative and positive battery supplies, as well as high voltage SLICs. It provides crowbar mode protection for both TIP and RING lines. The surge suppression is SO-8 wide assumed for each wire by two thyristor structures, LCP12 one dedicated to positive surges the second one for negative surges. Both positive and negative threshold levels are programmable by two gates. Features LCP12 can be used to help equipment to meet various standards such as UL1950, IEC 60950 / Protection IC recommended for ringing SLICs CSAC22.2, UL1459 and TIA-968-A. LCP12 Wide firing voltage range: -120 V to +120 V pinout and clearance is compatible with UL60950. Low gate triggering current: I = 5 mA max Resin meets UL94 V0. G Peak pulse current: I = 50 A (10/1000 s) PP LCP12 is UL497B approved - file: E136224. Holding current: I = 150 mA min. H The LCP12 associated with Epcos PTC model B59173C1130A151 is compliant with Applications ITU TK20/K21 (4 kV lightning and AC power fault tests). Dual battery supply voltage SLICs Central office (CO) Figure 1. Functional diagram TIP Private branch exchange (PBX) Digital loop carrier (DLC) Digital subscriber line access multiplexer Gp Gn (DSLAM) Fiber in the loop (FITL) GND Wireless local loop (WLL) Hybrid fiber coax (HFC) RING ISDN terminal adapter Figure 2. Pin-out configuration Cable modem TIP NC Gn GND Gp GND RING NC TM: Trisil is a trademark of STMicroelectronics March 2014 DocID17500 Rev 4 1/10 This is information on a product in full production. www.st.comCharacteristics LCP12 1 Characteristics Table 1. Compliant with the following standards Minimum Required Peak surge Voltage Current series resistor Standard peak voltage (V) waveform waveform Rs to meet current (A) standard ( ) 2500 2/10 s 500 2/10 s 12 GR-1089 Core First level 1000 10/1000 s 100 10/1000 s 10 GR-1089 Core Second level 5000 2/10 s 500 2/10 s 24 GR-1089 Core Intra-building 1500 2/10 s 100 2/10 s 0 6000 150 35 ITU-T-K20/K21 4000 10/700 s 100 5/310 s 10 1500 37.5 0 8000 ESD contact discharge 0 ITU-T-K20 (IEC61000-4-2) 1/60 ns 15000 ESD air discharge 0 4000 10/700 s 100 5/310 s 14 IEC61000-4-5 4000 1.2/50 s 100 8/20 s 0 1500 10/160 s 200 10/160 s 20 TIA-968-A (formerly FCC part 68) type A 800 10/560 s 100 10/560 s 15 TIA-968-A (formerly FCC part 68) type B 1000 9/720 s 25 5/320 s 0 Table 2. Absolute maximum ratings (T = 25 C) amb Symbol Parameter Value Unit 10/1000 s 50 I Peak pulse current 5/310 s 80 A PP 2/10s 150 t = 0.2 s 11 Non repetitive surge peak on-state current (F = 50 Hz) p t = 1 s 7.5 I value specified for each line p TSM I A TSM t = 15 min. 3 I value can be applied on both lines at the same time p TSM (GND capability is twice the line I ) TSM V Negative battery voltage range -120 to 0 Gn V V Positive battery voltage range 0 to +120 Gp T Operating junction temperature range -40 to +125 C j T Storage temperature range -55 to +150 C stg T Lead solder temperature (10 s duration) 260 C L 2/10 DocID17500 Rev 4