Instruction Sheet 408--10376 ExtractionTool2063388-1 23 Mar 11 RevB PROPERUSEGUIDELINES CumulativeTraumaDisorderscanresultfromtheprolongeduseofmanuallypoweredhandtools.Handtoolsareintendedforoccasionaluseandlowvolume applications.Awideselectionofpoweredapplicationequipmentforextended--use,productionoperationsisavailable. Handle Sheet 408--9501. The pin and socket contacts are listed by part number in Figure 1. Read these instructions thoroughly before attempting to remove any contacts from the housings. Dimensions on this sheet are in millimeters with NOTE Tip inch equivalent dimensions in brackets . Figures and illustrations are for identification only and are i not drawn to scale. Plunger 2. DESCRIPTION PARTNUMBERS FORMINIATURERECTANGULAR(MR)CONTACTS Thetoolconsistsofametaltipandaplastichandle.The tip is inserted into the mating face of the housing, PIN SOCKET depressing the locking lances of the crimped contact. STRIP LP STRIP LP This action allows the contact to beextracted fromthe wire--entry face of the housing. 350018 350036 350019 350037 350171 350197 350184 350186 3. EXTRACTIONPROCEDURE 350183 350185 350665 350666 350663 350664 350696 350697 The procedures which follow are recommended to extractacrimpedcontactfrom ahousing. SeeFigures 350684 350685 ------ ------ 2 and 3. 350694 350695 ------ ------ Proceed as follows: 350968 640579 641294 641300 350967 640545 ------ ------ 1. Grasp wire of contact to be removed. Push contact toward mating face of connector and hold FORMINIATUREUNIVERSALMATE--N--LOK*CONTACTS in this position. This will disengage contact locking PIN SOCKET lance from shoulder of cavity. STRIP LP STRIP LP 2. While holding wire, place tool releasing barrel 170359 170363 170361 170365 over end of contact and push straight into cavity 170360 170364 170362 170366 until it bottoms. The locking lance is now released. 171636 171638 171637 171639 3. Keep releasing barrel firmly bottomed in cavity FORCOMMERCIALPIN.062CONTACTS and depress plunger (handle). Contact will partially STRIP LP eject. 350629 ------ If difficulty is encountered in pushing contact NOTE 640391 ------ forward, Insertion Tool 91002--1 (tweezer type), maybeusedtoperformthetaskfromthewire Figure 1 i side of the housing. 1. INTRODUCTION 4. Pull contact from BACK of connector and Extraction Tool 2063388--1, Figure 1, is designed to remove tool from cavity. remove Miniature Rectangular (MR) contacts, Miniature Universal MATE--N--LOK contacts, or Before inserting contact into housing, reset NOTE Commercial .062 pin contacts from the housings locking lances to their original positions. Consult designed for these contacts. Information for the the Customer Drawing covering the specific i removal of Commercial .062 socket contacts with contact removed (or consult TE Connectivity Extraction Tool 844134--1 can be found on Instruction Engineering) for correct setting of locking lances. E2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company TOOLING ASSISTANCE CENTER 1--800--722--1111 This controlled document is subject to change. 1 of 2 All Rights Reserved PRODUCT INFORMATION 1--800--522--6752 For latest revision and Regional Customer Service, visit our website at www.te.com TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. LOCB *Trademark. Other logos, product and/or Company names may be trademarks of their respective owners.408-10376 Wire 1 Wire Wire Wire 1 4 4 Plug Contact Cavity Locking Lances Plunger (Ref Plunger (Ref 3 3 Pin Socket Contact 2 Contact 2 Releasing Barrel Releasing Barrel Figure 2 Figure 3 4. MAINTENANCEANDINSPECTION Additional tools can be purchased from: To ensure proper operation, the tool should conform TYCO ELECTRONICS CORPORATION to the dimensions provided in Figure 4. It is CUSTOMER SERVICE (38--35) recommended that the tool be inspected immediately P. O. BOX 3608 on its arrival and at regularly scheduled intervals. The HARRISBURG, PA 17105--3608 tool is not repairable and should be replaced when worn or damaged. It is recommended that the tool be 5. REVISIONSUMMARY stored in a clean, dry place and cleaned with a soft, lint--free cloth. S Updated document to corporate requirements. NOTE: Not to Scale 19.05 .750 Ref 2.03 .080 Ref 2.54 .100 Ref 60.60 2.386 Ref Figure 4 2 of 2 RevB